manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

vi

NetWare

For setting up the machine as a network printer in a NetWare environment, see
p.39 “NetWare Configuration”. The Network Interface Board allows you to use
the machine as either a print server or a remote printer.
For more information about setting up the clients, see the following pages.
• Windows 95/98/Me 

⇒

 p.58 “Windows 95/98/Me” 

• Windows 2000 

⇒

 p.59 “Windows 2000” 

• Windows NT 4.0 

⇒

 p.60 “Windows NT 4.0” 

Configuring the machine as a print server

A dedicated NetWare print server is not required because the machine can be
configured as a print server.

The actual procedures for configuring the machine depend on the NetWare ver-
sion.
• NetWare 3.x 

⇒

 p.44 “Setting Up as a Print Server” 

• NetWare 4.x, 5/5.1 

⇒

 p.51 “Setting Up as a Print Server” 

NetWare
File Server

Print Server

Windows 95 / 98/Me

Windows 2000

Windows NT 4.0

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Oki Okipage8z Limited Warranty preview
Okipage8z
Brand: Oki Pages: 16
Olivetti PR2 plus Service Manual preview
PR2 plus
Brand: Olivetti Pages: 179
Olivetti JS-505 Service Manual preview
JS-505
Brand: Olivetti Pages: 36
Oki B6200 Series Maintenance Manual preview
B6200 Series
Brand: Oki Pages: 679
Oki PRO511DW Manual preview
PRO511DW
Brand: Oki Pages: 40
OKIDATA Pacemark 3410 Service Handbook preview
Pacemark 3410
Brand: OKIDATA Pages: 308
OKIDATA Pacemark 3410 Instruction Manual preview
Pacemark 3410
Brand: OKIDATA Pages: 9
OKIDATA MICROLINE 320 Quick Manual preview
MICROLINE 320
Brand: OKIDATA Pages: 2
Oki Microline 8480 FB Setup Manual preview
Microline 8480 FB
Brand: Oki Pages: 12
Olympus P-10 Supplementary Manual preview
P-10
Brand: Olympus Pages: 2
Olympus P-10 Instruction Manual preview
P-10
Brand: Olympus Pages: 148
Lexmark X2650 - Color Printer 3-IN-1 Specifications preview
X2650 - Color Printer 3-IN-1
Brand: Lexmark Pages: 2
SNBC BTP-R880NP Programming Manual preview
BTP-R880NP
Brand: SNBC Pages: 78
KIP KIP 7000 Parts Manual preview
KIP 7000
Brand: KIP Pages: 103
Xerox WorkCentre 7655 Evaluator Manual preview
WorkCentre 7655
Brand: Xerox Pages: 24
Citizen CBM1000II RF User Manual preview
CBM1000II RF
Brand: Citizen Pages: 133
OmniPrint FreeJet320 TX User Manual preview
FreeJet320 TX
Brand: OmniPrint Pages: 44
Xerox WorkCentre PRO 35 Specifications preview
WorkCentre PRO 35
Brand: Xerox Pages: 13

Brands by name

Popular brands

Load more brands