manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Installing Options

24

2

Note

❒

Be sure to return the screwdriv-
er to the paper tray after using it.

❒

Print a configuration page to
confirm that the unit is properly
installed. See 

"Printing a Config-

uration Page"

 in the Printer Ref-

erence, on the CD-ROM labeled
"Operating Instructions".

Connecting the 1394 interface cable to 
the printer

AAAA

Attach the 1394 interface cable to
the jack on the board.

Both jacks are available.

BBBB

Connect the other end of the 1394
interface cable to the computer or
the other IEEE 1394 node.

Note

❒

The 1394 Interface Unit could not
receive data from more than one
PC at the same time. In this case, an
error message appears. The printer
can accept data sent from other
computers, after the first print job
has finished.

❒

The bidirectional transmissions
are not supported by the 1394 In-
terface Unit.

❒

When the 1394 Interface Unit is in-
stalled successfully, the printer icon
automatically changes from "Use
Printer Offline" to "Ready", accord-
ing to the 1394 interface cable plug.

❒

To use the 1394 Interface Unit, con-
figure the unit from the control
panel of the printer.

Printing with SCSI Print

You can print by directly connecting
the computer to the printer via the
1394 Interface cable and using the
SCSI print client function provided
with Windows 2000.

Limitation

❒

This function is available under
Windows 2000 only. It is not avail-
able under Windows 95/98/Me or
Windows NT 4.0.

❖

❖

❖

❖

Installing the Printer Driver

• “SCSI print” must be set active

from the control panel. For
more information, see p.34
“IEEE 1394 Configuration”.

• If the connected printer's driver

is not installed, follow the pro-
cedures below.

A

Connect this machine to your
computer with the 1394 in-
terface cable.

B

Press 

[

Cancel

]

 when "Detect

New Hardware Wizard" ap-
pears. If the same wizard re-
appears, press 

[

Cancel

]

 again.

C

Insert the printer driver CD-
ROM into the computer.

• For the port selection, select the

IEEE 1394 port.

• For more information about the

installation of the printer driv-
er,see p.37 “Installing the Print-
er Driver and Software”.

AP3ENSetup-F-ricoh_FM.book  Page 24  Friday, October 5, 2001  2:43 PM

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

GCC Technologies Elite 12N Network Manual preview
Elite 12N
Brand: GCC Technologies Pages: 63
GCC Technologies Elite XL-1208 Supplementary Manual preview
Elite XL-1208
Brand: GCC Technologies Pages: 9
GCC Technologies Elite XL User Manual preview
Elite XL
Brand: GCC Technologies Pages: 199
Xerox DocuColor 6060 Recommended Materials List preview
DocuColor 6060
Brand: Xerox Pages: 4
Lexmark 7016-630 Service Manual preview
7016-630
Brand: Lexmark Pages: 455
Xerox WorkCentre Pro 40 Specification preview
WorkCentre Pro 40
Brand: Xerox Pages: 14
Magicard Tango 2e Brochure preview
Tango 2e
Brand: Magicard Pages: 2
Magicard Tango 2e Quick Start Manual preview
Tango 2e
Brand: Magicard Pages: 2
BIXOLON SRP-500 Command Manual preview
SRP-500
Brand: BIXOLON Pages: 29
Olivetti d-Color MF280 Functions preview
d-Color MF280
Brand: Olivetti Pages: 74
Star SM-S301 Hardware Manual preview
SM-S301
Brand: Star Pages: 24
Oki C9000 Series User Manual preview
C9000 Series
Brand: Oki Pages: 204
Kashino Technology CSN-A1K User Manual preview
CSN-A1K
Brand: Kashino Technology Pages: 72
E-Pos TEP-220M User Manual preview
TEP-220M
Brand: E-Pos Pages: 21
Konica Minolta accuriopress c6085 Operation Manual preview
accuriopress c6085
Brand: Konica Minolta Pages: 81
Oki ES9170 MFP Quick Start Manual preview
ES9170 MFP
Brand: Oki Pages: 92
Citizen CT-S251 User Manual preview
CT-S251
Brand: Citizen Pages: 255
Minolta PAGEWORKS 8E User Manual preview
PAGEWORKS 8E
Brand: Minolta Pages: 255

Brands by name

Popular brands

Load more brands