manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

4

Formatting Printer Hard Disk 
Type 4510

If you are formatting the Printer Hard
Disk from the menu, follow the pro-
cedures below while using the control
panel.

A

Press 

{

{

{

{

Menu

}

}

}

}

.

 “Menu” appears on the panel dis-
play.

B

Press 

{

{

{

{U

U

U

U}

}

}

}

 or 

{

{

{

{T

T

T

T}

}

}

}

 to display the

“Maintenance” menu.

  Menu:

   Maintenance

C

Press 

{

{

{

{

Enter 

q

q

q

q

}

}

}

}

.

The following message appears on
the panel display.

  Menu:

   Image Density

D

Press 

{

{

{

{U

U

U

U}

}

}

}

 or 

{

{

{

{T

T

T

T}

}

}

}

 to display

“HDD Format”.

  Menu:

   HDD Format

Note

❒

If "HDD Format" is not dis-
played, the Printer Hard Disk is
not installed properly. In such a
case, reinstall from step 

B

.

E

Press 

{

{

{

{

Enter 

q

q

q

q

}

}

}

}

.

The following message appears on
the panel display.

  HDD Format:

  Press# To Start

F

Press 

{

{

{

{

Enter 

q

q

q

q

}

}

}

}

.

Important

❒

Do not turn off the printer while
formatting the Printer Hard
Disk. Turning off the printer
while formatting the Printer
Hard  Disk  can  damage  the
Printer Hard Disk.

If you successfully format the
Printer Hard Disk, the following
message appears on the panel dis-
play.

  Format Completed

  Restart Printer

Note

❒

If you fail, see 

“Troubleshooting”

in the Printer Reference, on the
CD-ROM labeled "Operating
Instructions".

G

Turn off the power switch, and
then back on.

Copyright©2001

G065-8539

Printed in Japan

UE  USA

EE   GB

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Xyron FPO User Manual preview
FPO
Brand: Xyron Pages: 6
Xerox 7700 Setup Manual preview
7700
Brand: Xerox Pages: 2
Xerox 7700 Setup And Quick Reference Manual preview
7700
Brand: Xerox Pages: 40
Xerox 7700 Advanced Features And Troubleshooting Manual preview
7700
Brand: Xerox Pages: 69
Xerox 7700 Install Manual preview
7700
Brand: Xerox Pages: 42
Raymarine e7 Installation And Operation Handbook preview
e7
Brand: Raymarine Pages: 135
Xerox WorkCentre 5325 Administrator'S Manual preview
WorkCentre 5325
Brand: Xerox Pages: 160
Xerox WorkCentre 5016 Specification preview
WorkCentre 5016
Brand: Xerox Pages: 2
Xerox WorkCentre 490cx Online User'S Manual preview
WorkCentre 490cx
Brand: Xerox Pages: 258
Xerox WorkCentre 4260 Series System Administration Manual preview
WorkCentre 4260 Series
Brand: Xerox Pages: 210
Xerox WorkCentre 3550 Information Manual preview
WorkCentre 3550
Brand: Xerox Pages: 32
Xerox WorkCentre 3315DN System Administrator Manual preview
WorkCentre 3315DN
Brand: Xerox Pages: 191
Xerox WORKCENTER 5222 Reference Manual preview
WORKCENTER 5222
Brand: Xerox Pages: 28
Xerox VersaLink C71 Series User Documentation preview
VersaLink C71 Series
Brand: Xerox Pages: 247
Xerox VersaLink C7000 Installation Manual preview
VersaLink C7000
Brand: Xerox Pages: 2
Xerox VersaLink C505 Quick Use Manual preview
VersaLink C505
Brand: Xerox Pages: 21
Xerox VersaLink B71 Series User Documentation preview
VersaLink B71 Series
Brand: Xerox Pages: 234
Xerox WorkCentre 6505 Brochure preview
WorkCentre 6505
Brand: Xerox Pages: 4

Brands by name

Popular brands

Load more brands