manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

NetWare Configuration

50

4

NetWare 4.x, 5/5.1 - Advanced Settings

The actual procedures for configuring the machine vary depending on whether
the Network Interface Board is configured as a print server or as a remote print-
er. This section describes how to configure it in the NetWare 4.x, 5/5.1 environ-
ment.

❖

❖

❖

❖

To use NetWare 5/5.1

• If you use Pure IP, configure the machine to use the TCP/IP protocol. For

more information about how to make the settings, see the Setup Guide.

Preparation

The following procedures use the Property Sheet method in configuring the
Network Interface Board. If you configure the Network Interface Board as a
NetWare print server for the first time, we recommend you use the Wizard
method. 

⇒

 p.41 “Quick Setup Using the NIB Setup Tool Wizard” 

Note

❒

This section assumes NetWare is functional and that the necessary environ-
ment for the NetWare Print Service is available.

❒

You should install the client software released from Novell in Windows be-
fore running the NIB Setup Tool for configuring in NDS mode or using Win-
dows NT 4.0.

Install the NIB Setup Tool

Print Server

Remote Printer

Basic Procedure

Configure the Network Interface Board

Configure the NetWare

Start the print server

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

QMS 3260 Getting Started Manual preview
3260
Brand: QMS Pages: 86
Oce COLOR SYSTEM 110 Operator'S Manual preview
COLOR SYSTEM 110
Brand: Oce Pages: 392
Sagem TX 20 Field Maintenance Manual preview
TX 20
Brand: Sagem Pages: 86
Kyocera Mita FS-1050 Operation Manual preview
FS-1050
Brand: Kyocera Mita Pages: 209
Radio Shack Line Printer VIII Hardware Manual preview
Line Printer VIII
Brand: Radio Shack Pages: 54
Xerox WorkCentre PE120i Evaluator Manual preview
WorkCentre PE120i
Brand: Xerox Pages: 8
Ricoh P 501 Setup Manual preview
P 501
Brand: Ricoh Pages: 24
Xerox 4250 - WorkCentre - Copier Specifications preview
4250 - WorkCentre - Copier
Brand: Xerox Pages: 4
Xerox DocuPrint C6 User Manual preview
DocuPrint C6
Brand: Xerox Pages: 78
Star Micronics NX-2450 User Manual preview
NX-2450
Brand: Star Micronics Pages: 194
Kyocera ECOSYS P5021cdw Frequently Asked Questions Manual preview
ECOSYS P5021cdw
Brand: Kyocera Pages: 31
Olivetti DR N17 Service Manual preview
DR N17
Brand: Olivetti Pages: 558
Tally T2140 Maintenance Manual preview
T2140
Brand: Tally Pages: 14
Xerox  Manual preview

Brand: Xerox Pages: 48
Oki ES7470x MFP User Manual preview
ES7470x MFP
Brand: Oki Pages: 78
Canon PIXMA MG2220 Series Getting Started Manual preview
PIXMA MG2220 Series
Brand: Canon Pages: 4
Canon PIXMA TR152 Getting Started preview
PIXMA TR152
Brand: Canon Pages: 16
Canon PIXMA TS3310 Getting Started preview
PIXMA TS3310
Brand: Canon Pages: 28

Brands by name

Popular brands

Load more brands