manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Printer Utility for Mac

18

2

Downloading PS Fonts

You can download the PS fonts to the printer's memory or hard disk drive.

Important

❒

The following procedures to download the fonts assume that you are a sys-
tem administrator. If you are not, be sure to consult your system administra-
tor.

❒

If the printer restarts, all the printer settings return to their defaults.

❒

Confirm that Macintosh and the printer are connected with Appletalk.

Note

❒

Some fonts cannot be downloaded.

❒

Before downloading, read the documentation about the fonts you want to
use.

AAAA

Select 

[

Download PS Fonts...

]

 on the 

[

File

]

 menu.

BBBB

Click 

[

Add to list

]

.

The dialog box to select fonts appears.

CCCC

Click to select the desired font files, and then click 

[

Open

]

.

The list of selectable font names appears.

DDDD

After adding all the fonts you want to download, click 

[

OK

]

.

The dialog box of selected fonts to download appears.

EEEE

Click 

[

Download

]

.

The fonts begin to download, and the download status is shown.

Important

❒

During the download, do not turn off the power switch, operate the panel
or open or close the cover.

FFFF

When the completion message appears, click 

[

OK

]

.

GGGG

Click 

[

Cancel

]

.

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

IBM 3130 Planning Manual preview
3130
Brand: IBM Pages: 112
Canon Color imageCLASS MF8580Cdw User Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 750
Canon ImageCLASS 2300 Setup Sheet preview
ImageCLASS 2300
Brand: Canon Pages: 8
Canon Color imageCLASS MF8580Cdw Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 750
Canon Color imageCLASS 8180c Facsimile Manual preview
Color imageCLASS 8180c
Brand: Canon Pages: 95
Canon GP200 Installation Instructions preview
GP200
Brand: Canon Pages: 4
Canon CFX-B380 IF Parts List preview
CFX-B380 IF
Brand: Canon Pages: 49
Canon ImageCLASS 2300 Basic Manual preview
ImageCLASS 2300
Brand: Canon Pages: 156
Canon FaxPhone L90 Reference Manual preview
FaxPhone L90
Brand: Canon Pages: 193
QMS 3225 Tray Module Installation Manual preview
3225
Brand: QMS Pages: 24
Canon imageCLASS D1120 User Manual preview
imageCLASS D1120
Brand: Canon Pages: 36
Canon ImageCLASS 2300 Remote Ui Manual preview
ImageCLASS 2300
Brand: Canon Pages: 44
Canon FAXPHONE L75 Software User'S Manual preview
FAXPHONE L75
Brand: Canon Pages: 66
Oki C5800 Brochure & Specs preview
C5800
Brand: Oki Pages: 6
Oki C7300 Référence Matérielle preview
C7300
Brand: Oki Pages: 44
Oki C7500 Enhancements Manual preview
C7500
Brand: Oki Pages: 13
Oki C7300 Software Installation Manual preview
C7300
Brand: Oki Pages: 20
Oki C7300 Specifications preview
C7300
Brand: Oki Pages: 2

Brands by name

Popular brands

Load more brands