manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

39

4. NetWare Configuration

This chapter describes how to configure the machine to use as a print server or
a remote printer in a NetWare environment.

Note

❒

NetWare must be set to active using the machine's control panel. For more in-
formation about how to set it, see the Setup Guide.

Installing the NIB Setup Tool 

A utility called the NIB Setup Tool is provided to configure the machine to work
in a network environment. This section describes how to install the SmartNet-
Monitor for Admin, and how to run the NIB Setup Tool.

Limitation

❒

The NIB Setup Tool is supported to work with the following operating sys-
tems.
• Microsoft Windows 95/98/Me
• Microsoft Windows 2000
• Microsoft Windows NT 4.0

❖

❖

❖

❖

SmartNetMonitor for Admin

Using a printer in a NetWare environment, configure the NetWare printing
environment by using SmartNetMonitor for Admin.

Note

❒

If you configure the NetWare printing environment by using SmartNet-
Monitor for Admin under the following environments, NetWare Client
provided by Novell is required.
• NDS mode in Windows 95/98
• NDS or Bindary mode in Windows 2000/Windows NT 4.0

❖

❖

❖

❖

Printers listed by SmartNetMonitor for Admin

SmartNetMonitor for Admin displays a list of printers, which are connected
to the network.
If you cannot find out the printer from the displayed list, refer to the config-
uration page printed from the printer. For more information about printing a
configuration page, see the Setup Guide.

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Oki B2200 Setup Manual preview
B2200
Brand: Oki Pages: 24
VAF instruments 247 Technical Manual preview
247
Brand: VAF instruments Pages: 24
Xerox 770 Safety Manual preview
770
Brand: Xerox Pages: 24
Xerox DocuColor 242 Manual preview
DocuColor 242
Brand: Xerox Pages: 128
SPRT SP-RMD17 User Manual preview
SP-RMD17
Brand: SPRT Pages: 17
Magicard Pronto 100 User Manual preview
Pronto 100
Brand: Magicard Pages: 42
Durst Automatic Photo Book Station Specifications preview
Automatic Photo Book Station
Brand: Durst Pages: 2
Konica Minolta bizhub 654 Using preview
bizhub 654
Brand: Konica Minolta Pages: 1
Canon IMAGERUNNER 7086 Brochure & Specs preview
IMAGERUNNER 7086
Brand: Canon Pages: 14
Canon imageRUNNER 5055 Brochure & Specs preview
imageRUNNER 5055
Brand: Canon Pages: 4
Canon imageRUNNER ADVANCE C2225 Service Manual preview
imageRUNNER ADVANCE C2225
Brand: Canon Pages: 109
Canon imageRUNNER ADVANCE 525 I Faq Manual preview
imageRUNNER ADVANCE 525 I
Brand: Canon Pages: 44
Canon imageRunner 60 Brochure & Specs preview
imageRunner 60
Brand: Canon Pages: 6
Canon imageRUNNER ADVANCE C2020 Operating Manual preview
imageRUNNER ADVANCE C2020
Brand: Canon Pages: 48
Canon imageRUNNER 5570 Service Manual preview
imageRUNNER 5570
Brand: Canon Pages: 46
Canon imageRunner Advance 6255 Service Manual preview
imageRunner Advance 6255
Brand: Canon Pages: 108
Canon imageRUNNER ADVANCE 525i III Getting Started preview
imageRUNNER ADVANCE 525i III
Brand: Canon Pages: 20
Canon imageRUNNER ADVANCE 6255i User Manual preview
imageRUNNER ADVANCE 6255i
Brand: Canon Pages: 394

Brands by name

Popular brands

Load more brands