manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

System Menu

119

6

Edge Smoothing

You can set whether Edge Smoothing is enabled. When it is on, 
jagged lines appear more smoothly. Set it to off when the print im-
age contains fine gradation in tone.

• On
• Off

Note

❒

Default: Off

❒

If "Toner Saving" is "On", "Edge Smoothing" is ignored even if 
it is "On".

Resolution

You can set the print resolution in dots per inch.

❖

❖

❖

❖

PCL

300 dpi, 600 dpi

❖

❖

❖

❖

PS

300 dpi, 600 dpi

❖

❖

❖

❖

TIFF

200 dpi, 300 dpi, 400 dpi, 600 dpi

Note

❒

Default: 600 dpi

Toner Saving

You can select whether or not Toner Saving is enabled.

• On
• Off

Note

❒

Default: Off

❒

If "Toner Saving" is "On", "Edge Smoothing" is ignored even if 
it is "On".

Spool Printing

When "On" is selected, the entire print data is spooled to the Print-
er Hard Disk before printing.

• On

• Off

Note

❒

Default: Off

Limitation

❒

"Spool Printing" does not appear unless the optional Printer 
Hard Disk is installed.

Menu

Description

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Canon MX490 Series Setup Manual preview
MX490 Series
Brand: Canon Pages: 11
Canon MX490 Series Quick Help Manual preview
MX490 Series
Brand: Canon Pages: 2
Canon Photura 135 Review preview
Photura 135
Brand: Canon Pages: 12
Canon PIXMA Pro9000 Mark II Series Release Note preview
PIXMA Pro9000 Mark II Series
Brand: Canon Pages: 4
Canon PowerShot S330 Digital ELPH Technical Information preview
PowerShot S330 Digital ELPH
Brand: Canon Pages: 2
Canon PowerShot S400 Digital Elph Reference Manual preview
PowerShot S400 Digital Elph
Brand: Canon Pages: 271
Canon PowerShot S95 Printing Manual preview
PowerShot S95
Brand: Canon Pages: 6
Canon PowerShot S330 Digital ELPH Quick Start Manual preview
PowerShot S330 Digital ELPH
Brand: Canon Pages: 25
Canon Sure shot 80 tele User Manual preview
Sure shot 80 tele
Brand: Canon Pages: 24
Canon iPF720 - imagePROGRAF Color Inkjet Printer Brochure & Specs preview
iPF720 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 8
Canon i475D Series Setup Instructions preview
i475D Series
Brand: Canon Pages: 2
F+D Feinwerk- und Drucktechnik TOP-ino Operating Instructions Manual preview
TOP-ino
Brand: F+D Feinwerk- und Drucktechnik Pages: 22
Javelin J310 Quick Start preview
J310
Brand: Javelin Pages: 2
Xerox Phaser 6300 Service Manual preview
Phaser 6300
Brand: Xerox Pages: 13
Xerox 5550B - Phaser B/W Laser Printer Administrator'S Manual preview
5550B - Phaser B/W Laser Printer
Brand: Xerox Pages: 117
Xerox WorkCentre 3345 Quick Use Manual preview
WorkCentre 3345
Brand: Xerox Pages: 18
A&D AD-8115A Instruction Manual preview
AD-8115A
Brand: A&D Pages: 24
Ricoh AP204 Operator'S Manual preview
AP204
Brand: Ricoh Pages: 301

Brands by name

Popular brands

Load more brands