manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Printer Utility for Mac

20

2

Initializing the Printer Disk

When initializing the printer's hard disk, all the fonts downloaded to the print-
er's hard disk drive are deleted. Before initializing, be sure to check the fonts on
the hard disk drive.

Important

❒

When initializing the printer's hard disk drive from the operation panel, all of
the data on the printer's hard disk drive is deleted. Before initializing, be sure
to check the data on the hard disk drive.

AAAA

Select 

[

Initialize Printer's Disk...

]

 on the 

[

File

]

 menu.

The confirmation message appears.

Note

❒

To cancel initialization, click 

[

Cancel

]

.

BBBB

Click 

[

Execute

]

.

Initializing starts.

Important

❒

Do not turn off the power switch until initializing is completed, otherwise
the hard disk drive might be damaged.

CCCC

When the completion message appears, click 

[

OK

]

.

Page Setup

You can set the paper size on which to print “Print Fonts Catalogue” and “Prints
Fonts Sample”.

AAAA

Select 

[

Page Setup...

]

 on the 

[

File

]

 menu.

BBBB

Choose the paper size.

Printing Font Catalog

Print the names of fonts available on the printer.

Note

❒

The paper selected under 

[

Page Setup

]

 is used.

AAAA

Select 

[

Print Fonts Catalogue

]

 on the 

[

File

]

 menu.

BBBB

Click 

[

Print

]

.

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

OEC Compact Series Installation Procedure preview
Compact Series
Brand: OEC Pages: 28
Xerox DocuPrint C3055 DX Settings Manual preview
DocuPrint C3055 DX
Brand: Xerox Pages: 20
Printronix MVP 150 Manual preview
MVP 150
Brand: Printronix Pages: 5
Parkside 337019 2001 Translation Of The Original Instructions preview
337019 2001
Brand: Parkside Pages: 176
Konica Minolta BIZHUB 650 Installation And Use preview
BIZHUB 650
Brand: Konica Minolta Pages: 2
Citizen iDP-3210 Service Manual preview
iDP-3210
Brand: Citizen Pages: 46
IBM INFOPRINT HI-LITE COLOR 4005-HC2 Upgrade Manual preview
INFOPRINT HI-LITE COLOR 4005-HC2
Brand: IBM Pages: 10
Lexmark C53x Clearing Jams Manual preview
C53x
Brand: Lexmark Pages: 6
Oki ES9160 MFP Manual preview
ES9160 MFP
Brand: Oki Pages: 182
SPRT SP-RMD17 User Manual preview
SP-RMD17
Brand: SPRT Pages: 17
InkTec Jetrix LXi Series Manual preview
Jetrix LXi Series
Brand: InkTec Pages: 3
Oki MC160MFP Safety And Warranty Manual preview
MC160MFP
Brand: Oki Pages: 56
TE Connectivity T3212 Operator'S Manual preview
T3212
Brand: TE Connectivity Pages: 25
Ricoh MFD User Manual preview
MFD
Brand: Ricoh Pages: 14
Ricoh M897 Maintenance Manual preview
M897
Brand: Ricoh Pages: 20
Xerox WORKCENTRE 5735 Brochure & Specs preview
WORKCENTRE 5735
Brand: Xerox Pages: 8
Xerox WorkCentre 5019 Service Documentation preview
WorkCentre 5019
Brand: Xerox Pages: 457
MIMAKI JV5-320DS Operation Manual preview
JV5-320DS
Brand: MIMAKI Pages: 140

Brands by name

Popular brands

Load more brands