manualshive.com logo in svg

Lanier AP4510, Setup Manual


Share
Download
background image

Quick Setup Using the NIB Setup Tool Wizard

41

4

Quick Setup Using the NIB Setup Tool 
Wizard

With the NIB Setup Tool, you can easily set up a NetWare printing environment. 

Reference

For more information about installing the NIB Setup Tool, see p.39 “Installing
the NIB Setup Tool”.

You can select 

[

Wizard

]

 or 

[

Property Sheet

]

 as an installation method.

When you configure the Network Interface Board for the first time, use the Wiz-
ard method.
If you want to use the Property Sheet method, see p.44 “NetWare 3.x - Advanced
Settings” or p.50 “NetWare 4.x, 5/5.1 - Advanced Settings”.

Note

❒

This section assumes that NetWare is functional and that the necessary envi-
ronment for NetWare Print Services is available.

❒

If you configure the Network Interface Board in a NetWare environment us-
ing the NIB Setup Tool, you should install the client software released from
Novell in the following cases.
• Windows 95/98/Me in NDS mode configuration
• Windows NT 4.0 in NDS mode configuration
• Windows NT 4.0 in Bindery mode configuration
• Windows 2000 in NDS mode configuration
• Windows 2000 in Bindery mode configuration

AAAA

Log on to the Netware file server or the NDS tree as an Admin or Admin
equivalent.

BBBB

Run the NIB Setup Tool.

Reference

 

⇒

 p.40 “Running the NIB Setup Tool” 

CCCC

Click 

[

Wizard

]

 and click 

[

OK

]

.

The 

[

NIB Setup Tool - Network board list

]

 dialog box of the Network Interface

Board appears.

DDDD

Click 

[

IPX protocol

]

.

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Canon Pixma MG2400 Series Getting Started Manual preview
Pixma MG2400 Series
Brand: Canon Pages: 2
WaxJet 6100 Service Reference Manual preview
6100
Brand: WaxJet Pages: 131
Saxxot CRU-158 Operation Manual preview
CRU-158
Brand: Saxxot Pages: 13
SPRT SP-T6 User Manual preview
SP-T6
Brand: SPRT Pages: 28
EASYPRINT Compact CM User Documentation preview
Compact CM
Brand: EASYPRINT Pages: 37
Canon imageRUNNER 5075 Manual preview
imageRUNNER 5075
Brand: Canon Pages: 250
Ricoh Aficio SP C420DN Brochure & Specs preview
Aficio SP C420DN
Brand: Ricoh Pages: 4
SEWOO LK-P24 Quick Manual preview
LK-P24
Brand: SEWOO Pages: 17
Ricoh Aficio 3224C Service Manual preview
Aficio 3224C
Brand: Ricoh Pages: 781
Citizen CT-S4000DCL User Manual preview
CT-S4000DCL
Brand: Citizen Pages: 4
ABLE Systems Ap1300 Quick Start Manual preview
Ap1300
Brand: ABLE Systems Pages: 4
Kyocera Mita Ecosys FS-1800+ Installation Manual preview
Ecosys FS-1800+
Brand: Kyocera Mita Pages: 31
Ricoh SP C222DN Administration Manual preview
SP C222DN
Brand: Ricoh Pages: 284
MHM Digital V Pro Operating Instructions Manual preview
Digital V Pro
Brand: MHM Pages: 52
Kyocera EP C320DN Operation Manual preview
EP C320DN
Brand: Kyocera Pages: 72
Citizen CBM-810 User Manual preview
CBM-810
Brand: Citizen Pages: 32
Savin 2035DP Operating Instructions Manual preview
2035DP
Brand: Savin Pages: 106
InfoSight LabeLase 4000 Operation & Maintenance Manual preview
LabeLase 4000
Brand: InfoSight Pages: 35

Brands by name

Popular brands

Load more brands