Home
/
Lanier
/
AP4510
/
Setup Manual

Lanier AP4510, Setup Manual

Share

Page: 374 / 424

background image

Introduction

To get maximum versatility from this machine all operators should carefully read and follow the instruc-
tions in this manual. Please keep this manual in a handy place near the machine.

Please read the Safety Information before using this machine. It contains important information related
to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.

Notes

For use with the following machines

•

RICOH Aficio AP4510

•

Savin MLP45

•

Gestetner P7145

•

nashuatec P7145

•

Rex-Rotary P7145

•

LANIER 2145

Trademarks

PostScript is a registered trademark of Adobe Systems, Incorporated.

Sun, SunOS and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the
United States and other countries.

HP-UX is a registered trademark of Hewlett-Packard Company.

LINUX is a trademark of Linus Torvalds.

RED HAT is a registered trademark of Red Hat, Inc.

Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights in those marks.

«
...
372
373
374
375
376
...
»

Summary of Contents for AP4510









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP4510

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

Brand: Olympus Pages: 2

WorkCentre 5325

Brand: Xerox Pages: 160

WorkCentre 5016

Brand: Xerox Pages: 2

WorkCentre 490cx

Brand: Xerox Pages: 258

WorkCentre 4260 Series

Brand: Xerox Pages: 210

WorkCentre 3550

Brand: Xerox Pages: 32

WorkCentre 3315DN

Brand: Xerox Pages: 191

WORKCENTER 5222

Brand: Xerox Pages: 28

VersaLink C71 Series

Brand: Xerox Pages: 247

VersaLink C7000

Brand: Xerox Pages: 2

Brand: Xerox Pages: 21

VersaLink B71 Series

Brand: Xerox Pages: 234

WorkCentre 6505

Brand: Xerox Pages: 4

WorkCentre 6015

Brand: Xerox Pages: 16

Brand: Xerox Pages: 4

Brand: Xerox Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands