HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download | Manualshive

Page: 245 / 252

background image

Configuring the switch

245

Table 176

Access Control List Configuration controls

Control Description

Statistics

Enables or disables the statistics collection for the ACL.

Egress Port

Selects an egress port to add to the ACL.
The egress port ACL will not match a Layer 2 broadcast or multicast packet. The
egress port ACL will not match packets if the destination port is a trunk.

ACL Metering Configuration

To display the following form, go to the ACL Configuration Table form, and select an ACL number, or
open the Access Control Lists folder and click

Add ACL.

The following table describes the ACL Metering Configuration controls:

Table 177

ACL Metering Configuration controls

Control Description

Committed rate
(64 - 1000000 kb/s)

Configures the committed rate, in Kilobits per second. The committed rate must be a
multiple of 64.

Maximum burst Size

(32 - -4096 kb/s)

Configures the maximum burst size, in Kilobits. Enter one of the following values for

mbsize

: 32, 64, 128, 256, 512, 1024, 2048, 4096

Set out of profile to Drop or

Pass

Configures the ACL Meter to either drop or pass out-of-profile traffic.

Enable

Enables or disables the ACL meter.

«
...
243
244
245
246
247
...
»

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Brand: Tactic Pages: 4

Brand: Radicom Pages: 62

Brand: Beyerdynamic Pages: 54

Brand: Rocstor Pages: 2

Brand: Rosewill Pages: 10

Brand: Exsys Pages: 2

Brand: Edimax Pages: 14

Brand: AzureWave Pages: 31

Brand: Hainbuch Pages: 108

Brand: Planet Pages: 72

Brand: Xoro Pages: 12

F8T031 - Bluetooth Wireless USB Printer Adapter Print Server

Brand: Belkin Pages: 93

isysNet ControlNet A Series

Brand: Parker Pages: 8

Wireless LAN Game Adapter W11

Brand: Hama Pages: 4

Brand: NCR Pages: 16

Brand: NCR Pages: 38

Brand: Uplift Desk Pages: 2

Brand: Lenze Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands