HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download

Page: 13 / 252

Browser-based interface basics

Introduction

Once you are properly logged in, the switch BBI displays in the Web browser-viewing window.

There are three main regions on the screen.

•

The Toolbar is used for selecting the context for your actions in the other windows.

•

The Navigation window is used for selecting particular items or features to act upon.

•

The Forms window is used for viewing or altering switch information.

Toolbar

The toolbar contains buttons and commands used to access and execute switch functions.

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Search results

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Reviews:

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Brands by name

Popular brands

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

Search results

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Reviews:

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Brands by name

Popular brands