manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

246

 

ACL Re-Mark Configuration 

To display the following form, go to the ACL Configuration Table form, and select an ACL number, or 
open the Access Control Lists folder and click 

Add ACL.

   

 

The following table describes the ACL Re-mark configuration controls: 

Table 178 

 ACL Re-mark Configuration controls 

 

Control Description 

Set in profile update method 

Defines the method used to update 802.1p priority updates, as follows:  

•

 

User defined – Sets the 802.1p priority for In-Profile packets based on the 

configured value.  

•

 

Use TOS precedence – Maps the TOS (Type of Service) priority to 
802.1p priority for In-Profile packets. 

•

 

Disabled – Disables 802.1p priority mapping for In-Profile packets. 

Set in profile user update priority 

(0-7) 

Defines 802.1p value. The value is the priority bits information in the packet 

structure.   

Set in profile update DSCP enable 

Enables or disables DSCP updates for In-Profile packets. 

Set in profile update DSCP (0-63) 

Sets the DiffServ Code Point (DSCP) of In-Profile packets to the selected value.

Set out of profile update DSCP 
enable 

Enables or disables DSCP updates for Out-of-Profile packets. 

Set out of profile update DSCP (0-63)  Sets the DiffServ Code Point (DSCP) of Out-of-Profile packets to the selected 

value. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

NEC VERSA TXI Important Information preview
VERSA TXI
Brand: NEC Pages: 2
NEC N8104-178 Startup Manual preview
N8104-178
Brand: NEC Pages: 47
NETGEAR WNHD3004 - High Performance Wireless-N HD Home Theatre Adapter User Manual preview
WNHD3004 - High Performance Wireless-N HD Home Theatre Adapter
Brand: NETGEAR Pages: 23
Intermec CN3E Series Quick Start Manual preview
CN3E Series
Brand: Intermec Pages: 2
Davis Instruments Coupler Kit Install Manual preview
Coupler Kit
Brand: Davis Instruments Pages: 4
Hainbuch MANOK Plus Operating Instructions Manual preview
MANOK Plus
Brand: Hainbuch Pages: 108
TRUlink 29573 User Manual preview
29573
Brand: TRUlink Pages: 36
3idee smsng-cv27 Assembly Instructions Manual preview
smsng-cv27
Brand: 3idee Pages: 7
Emulex LP982 Installation And Reference Manual preview
LP982
Brand: Emulex Pages: 19
TP-Link TL-WN751ND Quick Installation Manual preview
TL-WN751ND
Brand: TP-Link Pages: 15
Hama Bluetooth USB-Adapter Operating Instruction preview
Bluetooth USB-Adapter
Brand: Hama Pages: 4
Vivo MOUNT-HP23XW Instruction Manual preview
MOUNT-HP23XW
Brand: Vivo Pages: 4
Tektronix P7600 Series Instructions preview
P7600 Series
Brand: Tektronix Pages: 2
Rigol USB-GPIB-L Adapter User Manual preview
USB-GPIB-L Adapter
Brand: Rigol Pages: 20
Mitel MTL-300AN Setup Manual preview
MTL-300AN
Brand: Mitel Pages: 2
Jabra A120s Specifications preview
A120s
Brand: Jabra Pages: 2
Encore ENUBT-C2E Specifications preview
ENUBT-C2E
Brand: Encore Pages: 2
Steren COM-130 Quick Start Manual preview
COM-130
Brand: Steren Pages: 3

Brands by name

Popular brands

Load more brands