manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

226

 

Table 160 

 RIP Interface Configuration controls 

 

Control Descriptions 

Poisoned Reverse? 

When enabled, the switch uses split horizon with poisoned reverse. When disabled, 

the switch uses only split horizon. The default value is disabled.  

Triggered Updates? 

Enables or disables Triggered Updates. Triggered Updates are used to speed 
convergence. When enabled, Triggered Updates force a router to send update 

messages immediately, even if it is not yet time for the update message. The default 

value is disabled. 

Multicast Updates? 

Enables or disables multicast updates of the routing table (using address 
224.0.0.9). The default value is disabled. 

Split Horizon? 

Enables or disables split horizon. The default value is enabled. 

RIP Metric (1-15) 

Configures the route metric, which indicates the relative distance to the destination. 

The default value is 1. 

Authentication Type 

Configures the authentication type. The default is none. 

Authentication Key 

Configures the authentication key password. 

 

RIP Route Redistribution Configuration 

To display the following form, select 

Layer 3 > Routing Information Protocol > Static Route 

Redistribution, Fixed Route Redistribution, OSPF Route Redistribution, 

or

 OSPF External 

Route Redistribution.

  

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Airlink101 AWLL4030 Quick Installation Manual preview
AWLL4030
Brand: Airlink101 Pages: 4
Targus CHILL MAT PLUS User Manual preview
CHILL MAT PLUS
Brand: Targus Pages: 10
Digi Connectware Series Hardware Installation And Cable Manual preview
Connectware Series
Brand: Digi Pages: 2
Parani Parani-SD1100 User Manual preview
Parani-SD1100
Brand: Parani Pages: 48
P+S Technik PS-IMS-F3 User Manual preview
PS-IMS-F3
Brand: P+S Technik Pages: 2
TP-Link TL-WN323G User Manual preview
TL-WN323G
Brand: TP-Link Pages: 33
Hama 121976 User Manual preview
121976
Brand: Hama Pages: 4
LSI PCI to USB Host Adapter 60800 User Manual preview
PCI to USB Host Adapter 60800
Brand: LSI Pages: 10
K Tool International KTI63136 Owner'S Manual preview
KTI63136
Brand: K Tool International Pages: 18
SMC Networks EZ Connect SMC2670W Specification Sheet preview
EZ Connect SMC2670W
Brand: SMC Networks Pages: 2
Parallax 64007 Product Manual preview
64007
Brand: Parallax Pages: 7
Excelsecu Data Technology eSecu FIDO2 Pro+ Fingerprint Key User Manual preview
eSecu FIDO2 Pro+ Fingerprint Key
Brand: Excelsecu Data Technology Pages: 29
BenQ AWL300 User Manual preview
AWL300
Brand: BenQ Pages: 25
Allen-Bradley 140G-G-DRA Installation preview
140G-G-DRA
Brand: Allen-Bradley Pages: 4
Energenie EG-MC-009 User Manual preview
EG-MC-009
Brand: Energenie Pages: 9
DeLOCK 64074 User Manual preview
64074
Brand: DeLOCK Pages: 16
ZyXEL Communications omni.net LCD series Quick Start Manual preview
omni.net LCD series
Brand: ZyXEL Communications Pages: 53
National Instruments PCI-8232 Hardware Manual preview
PCI-8232
Brand: National Instruments Pages: 52

Brands by name

Popular brands

Load more brands