manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

169

 

VLAN Configuration 

To display the following form, go to the VLANs Configuration form. Select a VLAN ID, or open the Virtual 
LANs folder and click 

Add VLAN.

 

 

The commands on this form configure VLAN attributes, change the status of the VLAN, delete the VLAN, 
and change the port membership of the VLAN. 
By default, the VLAN menu option is disabled except VLAN 1, which is enabled all the time. The  

HP 1:10GbE switch supports a maximum of 1,000 VLANs. VLAN 4095 is reserved for switch 

management. 
The following table describes the VLAN Configuration controls: 

Table 115 

 VLAN Configuration controls 

 

Control Description 

VLAN Name 

Assigns a name to the VLAN or changes the existing name. The default VLAN name is 
the first one. 

VLAN ID (1-4095) 

Assigns a numeric identifier to the VLAN. 

VLAN State 

Enables or disables the VLAN. 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Targus ACA958USZ User Manual preview
ACA958USZ
Brand: Targus Pages: 8
3idee hp2x-o Assembly Instructions Manual preview
hp2x-o
Brand: 3idee Pages: 7
Mini Gadgets BUSHBABY2 Manual preview
BUSHBABY2
Brand: Mini Gadgets Pages: 5
ViewSonic VS10249 User Manual preview
VS10249
Brand: ViewSonic Pages: 69
TERK Technologies XMDirect XMDPIO110 Installation Manual preview
XMDirect XMDPIO110
Brand: TERK Technologies Pages: 6
Acard AEC-6712TU User Manual preview
AEC-6712TU
Brand: Acard Pages: 33
ZyXEL Communications ZyAIR G-220 User Manual preview
ZyAIR G-220
Brand: ZyXEL Communications Pages: 67
D-Link WL-211F User Manual preview
WL-211F
Brand: D-Link Pages: 22
Allen-Bradley PowerFlex 525 Application Technique preview
PowerFlex 525
Brand: Allen-Bradley Pages: 24
MSI US60SE User Manual preview
US60SE
Brand: MSI Pages: 53
KWorld USB Analog TV Stick II Installation Manual preview
USB Analog TV Stick II
Brand: KWorld Pages: 10
Steren Com-878 User Manual preview
Com-878
Brand: Steren Pages: 45
Dialogic CTbus Installation preview
CTbus
Brand: Dialogic Pages: 2
Belkin F5U116 Installation Manual preview
F5U116
Brand: Belkin Pages: 2
Belkin F8T001 User Manual preview
F8T001
Brand: Belkin Pages: 32
Belkin F5D6051 User Manual preview
F5D6051
Brand: Belkin Pages: 42
Belkin F5D8051ea User Manual preview
F5D8051ea
Brand: Belkin Pages: 52
Belkin Wireless G Router User Manual preview
Wireless G Router
Brand: Belkin Pages: 111

Brands by name

Popular brands

Load more brands