manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

159

 

Table 106 

 Switch Port Configuration controls 

 

Control Description 

PVID Tagging 

Disables or enables VLAN tag persistence. When disabled, the VLAN 

tag is removed from packets whose VLAN tag matches the port PVID. The 

default value is enabled. 

Port STP 

Turns Spanning Tree On or Off for this port. 

Default Port VLAN ID (1-4095) 

Sets the default VLAN number which will be used to forward frames 

which are not VLAN tagged. 
The default number is 1.  

NOTE: 

VLAN 4095 is reserved for switch management.

 

Flow Control 

Sets the flow control. The choices include: 

•

 

Receive flow control 

•

 

Transmit flow control 

•

 

Both receive and transmit flow control (default) 

•

 

No flow control 

Autonegotiation 

Enables or disables auto negotiation for the port. 

NOTE: 

Ports 19-21 are set to 10000 Mbps, and cannot be set to auto-

negotiate. 

Speed 

Sets the link speed. Not all options are valid on all ports. The choices 
include: 

•

 

“Any,” for automatic detection (default) 

•

 

10 Mbps 

•

 

100 Mbps 

•

 

1000 Mbps 

NOTE: 

Ports 19-21 are set to 10000 Mbps, and cannot be changed. 

Duplex mode 

Sets the operating mode. Not all options are valid on all ports. The 

choices include: 

•

 

“Any,” for auto negotiation (default) 

•

 

Full-duplex 

•

 

Half-duplex 

NOTE: 

Ports 19-21 are set to full duplex, and cannot be changed. 

Enable/Disable sending Link UP/Down 
Trap 

Enables or disables the sending of SNMP link up and link down traps. 
The default setting is enabled. 

Port Name 

Sets a name for the port. The assigned port name appears next to the 

port number on some information and statistics screens. 

Multicast Threshold 

Enables or disables multicast threshold limit.  
Limits the number of multicast packets to the specified value. If disabled 
(

dis

), the port forwards all multicast packets. 

Multicast Threshold Rate (0-262143) 

Configures the threshold rate for multicast packets, in packets per 
second. 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Yamaha UD-WL01 Connection Manual preview
UD-WL01
Brand: Yamaha Pages: 6
Z-Wave PAC01 Installation preview
PAC01
Brand: Z-Wave Pages: 5
Mercusys MW300UH Quick Installation Manual preview
MW300UH
Brand: Mercusys Pages: 59
i-tec C31VGA60HZP User Manual preview
C31VGA60HZP
Brand: i-tec Pages: 28
aqprox! appUSB150DAV2 User Manual preview
appUSB150DAV2
Brand: aqprox! Pages: 37
Sharkoon Mobile DAC Manual preview
Mobile DAC
Brand: Sharkoon Pages: 40
ZyXEL Communications ZyXEL ZyAIR 100 Quick Start Manual preview
ZyXEL ZyAIR 100
Brand: ZyXEL Communications Pages: 10
Targus APA107 Manual preview
APA107
Brand: Targus Pages: 4
ATI Technologies Component Video Adapter Installation And Setup User'S Manual preview
Component Video Adapter
Brand: ATI Technologies Pages: 16
TRENDnet TEW-226PC Quick Installation Manual preview
TEW-226PC
Brand: TRENDnet Pages: 11
NetComm NP745n Technical Specifications preview
NP745n
Brand: NetComm Pages: 1
Skross MUV Micro Manual preview
MUV Micro
Brand: Skross Pages: 2
X-media XM-UB3204 User Manual preview
XM-UB3204
Brand: X-media Pages: 7
B&B Electronics Quatech SSP-100 User Manual preview
Quatech SSP-100
Brand: B&B Electronics Pages: 40
Roving Networks RN-BTHID-RD-UM User Manual preview
RN-BTHID-RD-UM
Brand: Roving Networks Pages: 8
Laser 4599 Instructions preview
4599
Brand: Laser Pages: 2
Dynafit CRAMPON User Manual preview
CRAMPON
Brand: Dynafit Pages: 17
Compaq NC6136 User Manual preview
NC6136
Brand: Compaq Pages: 16

Brands by name

Popular brands

Load more brands