manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

195

 

IP Static Routes Configuration 

To display the following form, select 

Layer 3 > Network Routes

 (click the underlined text, not the 

folder). 

 

This form summarizes static route parameters.  
The following table describes IP Static Routes Configuration controls: 

Table 135 

 IP Static Routes Configuration controls 

 

Control Description 

Search Operation 

To focus the search for an IP static route, enter search parameters: 

•

 

Static Route ID 

•

 

Destination IP address and subnet mask 

•

 

Gateway IP address and subnet mask 

Fields that have a value of “any” are ignored during the search.  
Choose a search operation: 

•

 

or:

 Search for IP static routes specified in the Search range that meet any of the 

criteria entered. 

•

 

and:

 Search for IP static routes specified in the Search range that meet all of the 

criteria entered. 

Click 

Search

 to display IP static routes that fit the range and meet the criteria entered. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

D-Link AirPlus G DWL-G510 Quick Installaion Manual preview
AirPlus G DWL-G510
Brand: D-Link Pages: 12
Radio Shack 273-1668 Quick Start Manual preview
273-1668
Brand: Radio Shack Pages: 1
Belkin POWERLINE AV Quick Installation Manual preview
POWERLINE AV
Brand: Belkin Pages: 2
YOKOGAWA 94016 Series User Manual preview
94016 Series
Brand: YOKOGAWA Pages: 2
Netronix W121C User Manual preview
W121C
Brand: Netronix Pages: 87
Proyecson PAA20+ Installation Manual preview
PAA20+
Brand: Proyecson Pages: 148
Staubli PV-KBT4 UR Series Assembly Instructions Manual preview
PV-KBT4 UR Series
Brand: Staubli Pages: 12
Monster JHIU0109 Quick Manual preview
JHIU0109
Brand: Monster Pages: 2
Dynex DX-CRDRD User Manual preview
DX-CRDRD
Brand: Dynex Pages: 20
D-Link Vonage VTA-VR Quick Installation Manual preview
Vonage VTA-VR
Brand: D-Link Pages: 8
D-Link Vonage VTA-VR User Manual preview
Vonage VTA-VR
Brand: D-Link Pages: 23
D-Link WUS-B12 Manual preview
WUS-B12
Brand: D-Link Pages: 44
D-Link XTREME N DUAL BAND USB ADAPTER DWA-160 User Manual preview
XTREME N DUAL BAND USB ADAPTER DWA-160
Brand: D-Link Pages: 60
D-Link WNA-1330 User Manual preview
WNA-1330
Brand: D-Link Pages: 70
D-Link Xreme N DWA-160 User Manual preview
Xreme N DWA-160
Brand: D-Link Pages: 61
D-Link WUA-1340 User Manual preview
WUA-1340
Brand: D-Link Pages: 78
D-Link WDA-2320 RangeBooster G User Manual preview
WDA-2320 RangeBooster G
Brand: D-Link Pages: 81
D-Link WDA-1320 User Manual preview
WDA-1320
Brand: D-Link Pages: 80

Brands by name

Popular brands

Load more brands