manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

234

 

Table 167 

 VRRP General Configuration controls 

 

Control Descriptions 

Priority (1-254) 

Defines the election priority bias for this virtual router group. This can be any 

integer between 1 and 254. The default value is 100. 
During the master router election process, the routing device with the highest virtual 
router priority number wins. If there is a tie, the device with the highest IP interface 
address wins. If this virtual router’s IP address (

addr

) is the same as the one used 

by the IP interface, the priority for this virtual router will automatically be set to 255 

(highest). 
When priority tracking is used (

/cfg/l3/vrrp/track

 or 

/cfg/l3/vrrp/vr

 

#/track

), this base priority value can be modified 

according to a number of performance and operational criteria. 

Advertisement Interval (1-255)  Defines the time interval between VRRP master advertisements. This can be any 

integer between 1 and 255 seconds. The default is 1.  

Owner Preemption? 

Enables or disables master preemption. When enabled, if the virtual router group 

is in backup mode but has a higher priority than the current master, this virtual 
router will preempt the lower priority master and assume control. Note that even 
when 

preem

 is disabled, this virtual router will always preempt any other master if 

this switch is the owner (the IP interface address and virtual router 

addr

 are the 

same). By default, this option is enabled. 

Track other IP interface? 

When enabled, the priority for this virtual router will be increased for each other IP 
interface active on this switch. An IP interface is considered active when there is at 

least one active port on the same VLAN. This helps elect the virtual routers with the 

most available routes as the master. This command is disabled by default. 

Track VLAN switch ports? 

When enabled, the priority for this virtual router will be increased for each active 
port on the same VLAN. A port is considered “active” if it has a link and is 

forwarding traffic. This helps elect the virtual routers with the most available ports 

as the master. This command is disabled by default. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

D-Link WUA-1340 Manual preview
WUA-1340
Brand: D-Link Pages: 43
Teufel raumfeld one s Setup Manual preview
raumfeld one s
Brand: Teufel Pages: 24
TEXIO GP-600B Instruction Manual preview
GP-600B
Brand: TEXIO Pages: 49
TP-Link TL-PA201 STARTER Specifications preview
TL-PA201 STARTER
Brand: TP-Link Pages: 2
Aiphone RY-IP44 Programming Manual preview
RY-IP44
Brand: Aiphone Pages: 15
SMC Networks EZ Connect N SMCWUSBS-N User Manual preview
EZ Connect N SMCWUSBS-N
Brand: SMC Networks Pages: 64
l-com ARK-2404U-3 User Manual preview
ARK-2404U-3
Brand: l-com Pages: 34
COP-USA WE-7020S Integration Manual preview
WE-7020S
Brand: COP-USA Pages: 7
Eskridge 28 Service Manual preview
28
Brand: Eskridge Pages: 4
Danfoss VLT 2800 Manual preview
VLT 2800
Brand: Danfoss Pages: 166
Lanpro LP-570G Installation Manual preview
LP-570G
Brand: Lanpro Pages: 16
Maxnet WU 8702 - 1N User Manual preview
WU 8702 - 1N
Brand: Maxnet Pages: 39
CE Labs DCB101 Instruction Manual preview
DCB101
Brand: CE Labs Pages: 2
Compaq NC3131 User Manual preview
NC3131
Brand: Compaq Pages: 32
Adaptec ANA-7711C Getting Started Manual preview
ANA-7711C
Brand: Adaptec Pages: 12
Adaptec 78165 SAS/SATA RAID Datasheet preview
78165 SAS/SATA RAID
Brand: Adaptec Pages: 2
Adaptec AMM-1570 User Manual preview
AMM-1570
Brand: Adaptec Pages: 106
Adaptec AVA-2820 User Manual preview
AVA-2820
Brand: Adaptec Pages: 110

Brands by name

Popular brands

Load more brands