manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Dashboard

 

 

 

  

 

51

 

IP Interfaces Dashboard 

To display the following form, select 

Layer 3 > IP Interfaces

 (click the underlined text, not the folder). 

 

The following table describes the IP Interfaces Dashboard controls: 

Table 27 

 IP Interfaces Dashboard controls 

 

Control Description 

Search Range 

To search for an IP Interface, enter a range of IP Interface numbers in the From and To fields. 

Search Options 

To focus the search for an IP Interface, enter optional search parameters: 

•

 

IP Address 

•

 

Subnet Mask 

•

 

VLAN ID number 

•

 

IP Interface State 

Fields that have a value of “any” are ignored during the search.  
Choose a search operation: 

•

 

or:

 Search for IP Interfaces specified in the search range that meet any of the criteria 

entered. 

•

 

and:

 Search for IP Interfaces specified in the search range that meet all of the criteria 

entered. 

Click 

Search

 to display IP Interfaces that fit the range and meet the criteria entered. 

Status 

Shows the IP Interface status: enabled (green), disabled (red), or enabled but down (blue). 

IP Interface ID 

Displays the numeric identifier of the IP Interface. 

IP Address 

Displays the IP address of the IP Interface. 

Subnet Mask 

Displays the Subnet Mask of the IP Interface. 

Broadcast Address 

Displays the IP Broadcast address for this IP Interface. 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Hama Bluetooth USB-Adapter Version 1.2 Operating Instruction preview
Bluetooth USB-Adapter Version 1.2
Brand: Hama Pages: 8
Renkforce 2435399 Operating Instructions Manual preview
2435399
Brand: Renkforce Pages: 7
Edge Wireless BTR-2M User Manual preview
BTR-2M
Brand: Edge Wireless Pages: 5
Hi-flying Elfin-EE1X User Manual preview
Elfin-EE1X
Brand: Hi-flying Pages: 19
National Instruments 68M-50F STEP User Manual preview
68M-50F STEP
Brand: National Instruments Pages: 2
Magnadyne WC-USB-B Installation Instructions preview
WC-USB-B
Brand: Magnadyne Pages: 2
Aironet ISA3500 User'S Manual And Technical Reference Manual preview
ISA3500
Brand: Aironet Pages: 99
Digi Wavespeed S Configuration Manual preview
Wavespeed S
Brand: Digi Pages: 11
Hama 00049274 Instructions Manual preview
00049274
Brand: Hama Pages: 7
EtherWAN GE3000 User Manual preview
GE3000
Brand: EtherWAN Pages: 21
Lenovo Intel X520 Product Manual preview
Intel X520
Brand: Lenovo Pages: 17
Lenovo Flex System FC3172 Product Manual preview
Flex System FC3172
Brand: Lenovo Pages: 10
Lenovo QLogic Enhanced Gen 5 Product Manual preview
QLogic Enhanced Gen 5
Brand: Lenovo Pages: 10
Lenovo H230 - Desktop 4GB 1TB HDD Reference Manual preview
H230 - Desktop 4GB 1TB HDD
Brand: Lenovo Pages: 28
Lenovo Thinkpad 72W Slim User Manual preview
Thinkpad 72W Slim
Brand: Lenovo Pages: 52
Lenovo H215 User Manual preview
H215
Brand: Lenovo Pages: 37
Lenovo QLogic 8Gb FC Single-port Product Manual preview
QLogic 8Gb FC Single-port
Brand: Lenovo Pages: 7
Lenovo Y Series User Manual preview
Y Series
Brand: Lenovo Pages: 96

Brands by name

Popular brands

Load more brands