manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

Share
Download
HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download Page 156

 

 

 

Configuring the switch

 

 

 

  

 

156

 

Management Network Definition Configuration 

To display the following form, select 

System > Mgmt.

 

 

The following table describes the Management Network Definition Configuration controls: 

Table 105 

 Management Network Definition Configuration controls 

 

Control Description 

Index 

Displays the index number that identifies each management network. 

Management Network Address 

Adds a defined network through which switch access is allowed through 
Telnet, SNMP, or the Browser-based Interface (BBI). A range of IP 

addresses is produced when used with a network mask address. Specify 

an IP address in dotted-decimal notation. 

Management Network Subnet Mask 

Specify a mask address in dotted-decimal notation. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands