manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Dashboard

 

 

 

  

 

43

 

The following table describes the Switch Trunk Groups Dashboard controls: 

Table 20 

 Switch Trunk Groups Dashboard controls 

 

Control Description 

Status 

For each port in the Trunk Group, shows whether the port is down (red), up and 

forwarding (green) or in blocking state. 

Trunk Group 

Displays the numeric identifier of the Trunk Group. 

Switch Port 

Displays the port number of each port that is a member of the Trunk Group. 

STG 

Displays the Spanning Tree Group to which this trunk belongs. 

 

Trunk Hash Dashboard 

To display the following form, select 

Layer 2 > Trunk Hash.

 

 

The following table describes the Layer 2 (L2) Trunk Hash Dashboard controls:  

Table 21 

 Trunk Hash Dashboard controls 

 

Control Description 

Smac Hash 

Displays the status of the source MAC hash: enabled or disabled. 

Dmac Hash 

Displays the status of the destination MAC hash: enabled or disabled. 

Sip Hash 

Displays the status of the source IP hash: enabled or disabled. 

Dip Hash 

Displays the status of the source IP hash: enabled or disabled. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

3idee hp-32f Assembly Instructions Manual preview
hp-32f
Brand: 3idee Pages: 7
KEB Pre Series Instructions For Use Manual preview
Pre Series
Brand: KEB Pages: 17
3idee smsng-c24rg Assembly Instructions Manual preview
smsng-c24rg
Brand: 3idee Pages: 7
Rotel RDA 980 Owner'S Manual preview
RDA 980
Brand: Rotel Pages: 8
Patton electronics 14TB User Manual preview
14TB
Brand: Patton electronics Pages: 2
Exsys EX-47000 User Manual preview
EX-47000
Brand: Exsys Pages: 2
IBM OPTIONS User Manual preview
OPTIONS
Brand: IBM Pages: 60
Syba SD-EXP50025 User Manual preview
SD-EXP50025
Brand: Syba Pages: 2
StarTech.com USB312SAT3 Quick Start Manual preview
USB312SAT3
Brand: StarTech.com Pages: 2
3idee smsng-cv27 Assembly Instructions Manual preview
smsng-cv27
Brand: 3idee Pages: 7
ACTiSYS ACT-IR2000UL User Manual preview
ACT-IR2000UL
Brand: ACTiSYS Pages: 20
Ahlborn ALMEMO 8006-RTA3 Operating Instructions Manual preview
ALMEMO 8006-RTA3
Brand: Ahlborn Pages: 16
ZNYX NetBlaster ZX345 User Manual preview
NetBlaster ZX345
Brand: ZNYX Pages: 12
TP-Link TL-WN951N - IEEE 802.11b/g 802.11n Draft 2.0 PCI Wireless Adapter User Manual preview
TL-WN951N - IEEE 802.11b/g 802.11n Draft 2.0 PCI Wireless Adapter
Brand: TP-Link Pages: 41
3idee de-aw34 Assembly Instructions Manual preview
de-aw34
Brand: 3idee Pages: 7
Curtis Computer AP1075 Instructions preview
AP1075
Brand: Curtis Computer Pages: 2
D-Link DWL-G630 - AirPlus G 802.11g Wireless PC Card Manual preview
DWL-G630 - AirPlus G 802.11g Wireless PC Card
Brand: D-Link Pages: 52
Verbatim 49143 Quick Install Manual preview
49143
Brand: Verbatim Pages: 2

Brands by name

Popular brands

Load more brands