manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

Share
Download
HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download Page 207

 

 

 

Configuring the switch

 

 

 

  

 

207

 

Table 145 

 IGMP Snooping Configuration controls 

 

Control Descriptions 

Snooping VLANs with 

Fstleave 

Enables or disables FastLeave processing. FastLeave allows the switch to 

immediately remove a port from the IGMP port list, if the host sends a Leave 

message, and the proper conditions are met. This command is disabled by default. 
Add: Adds selected VLANs to the Snooping VLANs with Fstleave list. To add a 
VLAN, select the VLAN in the Snooping VLANs without Fstleave list, and click 

Add.

 

Remove: Removes selected VLANs from the Snooping VLANs with Fstleave list. 

 

IGMP Filters Configuration 

To display the following form, select 

Layer 3 > IGMP > IGMP Filters

 (click the underlined text, not the 

folder). 

 

This form summarizes IGMP filter parameters. Use IGMP filters to allow or deny a port to send and 

receive multicast traffic. 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands