manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Dashboard

 

 

 

  

 

59

 

Table 35 

 Route Map Dashboard controls 

 

Control Description 

Network Filter Action  Action associated with the network filter for the access list: permit or deny 

Enable/Disable 

Access List 

Status of the access list: enabled or disabled. 

 

Default Gateways Dashboard 

To display the following form, select 

Layer 3 > Default Gateways

 (click the underlined text, not the 

folder). 

 

The following table describes the Default Gateways Dashboard controls: 

Table 36 

 Default Gateways Dashboard controls 

 

Control Description 

Search Range 

To search for a Default Gateway, enter a range of Gateway numbers in the From and To 
fields. 

Search Options 

To focus the search for a Default Gateway, enter optional search parameters: 

•

 

IP Address 

•

 

Subnet Mask 

•

 

Default Gateway State 

Fields that have a value of “any” are ignored during the search.  
Choose a search operation: 

•

 

or:

 Search for Default Gateways specified in the search range that meet any of the 

criteria entered. 

•

 

and:

 Search for Default Gateways specified in the search range that meet all of the 

criteria entered. 

Click 

Search

 to display Default Gateways that fit the range and meet the criteria entered. 

Status 

Shows if the Default Gateway is 

enabled

 (green) or 

disabled

 (red). 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

cable matters 402031 Installation Instructions preview
402031
Brand: cable matters Pages: 2
cable matters 201049 User Manual preview
201049
Brand: cable matters Pages: 12
cable matters 102021 Manual preview
102021
Brand: cable matters Pages: 2
Therma-Stor Phoenix Window Adapter Owner'S Manual preview
Phoenix Window Adapter
Brand: Therma-Stor Pages: 4
NGS W-70W Automatic Manual preview
W-70W Automatic
Brand: NGS Pages: 40
Targus ACB10US1 Quick Start preview
ACB10US1
Brand: Targus Pages: 2
Asante AeroLAN AL1011 Quick Installation Manual preview
AeroLAN AL1011
Brand: Asante Pages: 2
Philips PowerLife 3LR12PBXC Specifications preview
PowerLife 3LR12PBXC
Brand: Philips Pages: 2
Billion AV 500 Features preview
AV 500
Brand: Billion Pages: 2
The Fisher MPX-100 Operating Instructions And Warranty preview
MPX-100
Brand: The Fisher Pages: 16
Cradlepoint CBA750 Series User Manual preview
CBA750 Series
Brand: Cradlepoint Pages: 89
Cradlepoint CBA750B Product Manual preview
CBA750B
Brand: Cradlepoint Pages: 172
Insignia NS-TADPT1USB Quick Setup Manual preview
NS-TADPT1USB
Brand: Insignia Pages: 2
Insignia NS-MTC1875 Quick Start Manual preview
NS-MTC1875
Brand: Insignia Pages: 2
EasySync USB2-H-6004 Quick Start Manual preview
USB2-H-6004
Brand: EasySync Pages: 2
3idee hp2xf-o Assembly Instructions preview
hp2xf-o
Brand: 3idee Pages: 4
Manhattan 303095 User Manual preview
303095
Brand: Manhattan Pages: 8
Eaton AQB-L400 Instructions For Use preview
AQB-L400
Brand: Eaton Pages: 2

Brands by name

Popular brands

Load more brands