manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Viewing statistics

 

 

 

  

 

127

 

The following table describes VRRP statistics: 

Table 85 

 Virtual Router Redundancy Protocol Statistics 

 

Statistic Description 

InAdvertisements 

The total number of VRRP advertisements that have been received. 

BadAdvertisements 

The total number of VRRP advertisements received that were dropped. 

OutAdvertisements 

The total number of VRRP advertisements that have been sent. 

BadVersion 

The total number of VRRP advertisements that had a bad version number. 

BadVrid 

The total number of VRRP advertisements that had a bad virtual router ID. 

BadAddress 

The total number of VRRP advertisements that had a bad address. 

BadData 

The total number of VRRP advertisements that had bad data. 

BadPassword 

The total number of VRRP advertisements that had a bad password. 

BadInterval 

The total number of VRRP advertisements that had a bad interval. 

 

Domain Name System Statistics 

To display the following form, select 

Layer 3 > Domain Name System.

 

 

The following table describes DNS statistics: 

Table 86 

 DNS Statistics 

 

Statistic Description 

DNS In Requests 

The total number of DNS request packets that have been received. 

Bad DNS Requests 

The total number of DNS request packets received that were dropped. 

DNS Out Requests 

The total number of DNS response packets that have been transmitted. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

3idee csl-f24 Assembly Instructions Manual preview
csl-f24
Brand: 3idee Pages: 7
3idee hp-m Assembly Instructions Manual preview
hp-m
Brand: 3idee Pages: 6
Gira 0582 00 Installation Instructions preview
0582 00
Brand: Gira Pages: 2
ZyXEL Communications PLA5206 Quick Start Manual preview
PLA5206
Brand: ZyXEL Communications Pages: 4
Rosewill RNX-G1LX Quick Installation Manual preview
RNX-G1LX
Brand: Rosewill Pages: 10
AGFEO HS-Module 30 Installation Instructions Manual preview
HS-Module 30
Brand: AGFEO Pages: 12
Qlogic SANblade QLA 2462 Datasheet preview
SANblade QLA 2462
Brand: Qlogic Pages: 2
Cameo WLN-1502 User Manual preview
WLN-1502
Brand: Cameo Pages: 19
TRUlink 29594 User Manual preview
29594
Brand: TRUlink Pages: 34
HP Z Series User Manual preview
Z Series
Brand: HP Pages: 40
HP Workstation Z600 Brochure preview
Workstation Z600
Brand: HP Pages: 2
HP StorageWorks FCA2214DC Implementation Manual preview
StorageWorks FCA2214DC
Brand: HP Pages: 9
HP SC44Ge Quickspecs preview
SC44Ge
Brand: HP Pages: 17
HP Workstation Z800 Specification preview
Workstation Z800
Brand: HP Pages: 73
HP Tc2110 - Server - 128 MB RAM Installation Manual preview
Tc2110 - Server - 128 MB RAM
Brand: HP Pages: 65
HP Workstation Z600 Specification preview
Workstation Z600
Brand: HP Pages: 75
HP Workstation Z600 Maintenance And Service Manual preview
Workstation Z600
Brand: HP Pages: 234
HP P3413A Installation And Configuration Manual preview
P3413A
Brand: HP Pages: 82

Brands by name

Popular brands

Load more brands