manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

237

 

The following table describes the IP Routing General Configuration controls: 

Table 170 

 IP Routing General Configuration controls 

 

Control Description 

IP Forwarding Enabled? 

Enables or disables IP Forwarding. 

Enable Forwarding Directed Broadcasts? 

Enables or disables forwarding directed broadcasts. 

IP Destination Re-ARP Interval (2-120 minutes) 

Sets the re-ARP period in minutes. The switch periodically 
sends ARP (Address Resolution Protocol) requests to 

refresh its address database. This command is used for 

setting the interval between ARP refreshes of the next IP 
address in the database. The default interval is 10 

minutes. 

Router ID 

Configures the router ID. 

 

QoS Priority CoS Configuration 

To display the following form, select 

QoS > 802.1p > Priority - CoS.

 

 

This form summarizes the QoS Priority – Class of Service parameters. Select a priority value to view the 

CoSQ For Priority form.  

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

StarTech.com 8STICUSB232SM3 Instruction Manual preview
8STICUSB232SM3
Brand: StarTech.com Pages: 2
W&T 33001 Manual preview
33001
Brand: W&T Pages: 18
IFM E80392 Operating Instructions Manual preview
E80392
Brand: IFM Pages: 10
Cognex IN-SIGHT Installation Reference preview
IN-SIGHT
Brand: Cognex Pages: 18
TP-Link TL-WN620G User Manual preview
TL-WN620G
Brand: TP-Link Pages: 33
Radio Shack Notebook Computer Universal 30W Power... Owner'S Manual preview
Notebook Computer Universal 30W Power...
Brand: Radio Shack Pages: 36
TP-Link TL-WN310G User Manual preview
TL-WN310G
Brand: TP-Link Pages: 37
Zero One EzSKY050 User Manual preview
EzSKY050
Brand: Zero One Pages: 10
Belkin F5D7051 User Manual preview
F5D7051
Brand: Belkin Pages: 44
Belkin F5D8073 User Manual preview
F5D8073
Brand: Belkin Pages: 44
Asante FriendlyNET Wireless USB Adapter User Manual preview
FriendlyNET Wireless USB Adapter
Brand: Asante Pages: 17
Patton electronics Patton SmartLink M-ATA Getting Started Manual preview
Patton SmartLink M-ATA
Brand: Patton electronics Pages: 86
Silicon Laboratories TOOLSTICK C8051F330 Manual preview
TOOLSTICK C8051F330
Brand: Silicon Laboratories Pages: 214
Improved Racing EFR-100 Instructions Manual preview
EFR-100
Brand: Improved Racing Pages: 12
Sandberg 135-74 Quick Manual preview
135-74
Brand: Sandberg Pages: 8
Sandberg 133-33 User Manual preview
133-33
Brand: Sandberg Pages: 9
Sandberg COM (RS232) User Manual preview
COM (RS232)
Brand: Sandberg Pages: 13
Sandberg Wireless N300 USB Manual preview
Wireless N300 USB
Brand: Sandberg Pages: 32

Brands by name

Popular brands

Load more brands