manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Dashboard

 

 

 

  

 

30

 

Switch Ports Dashboard 

To display the following form, select 

Switch Ports

 (click the underlined text, not the folder). 

 

The following table describes the Switch Ports Dashboard controls: 

Table 11 

 Switch Ports Dashboard controls 

 

Control Description 

Status 

Shows if the port is enabled (green) or disabled (black). 

Switch Port Info 

Summarizes the following port information: 

•

 

STP:

 Shows if the port has Spanning Tree Protocol enabled or disabled. 

•

 

rmon:

 Shows if RMON is enabled or disabled.  

•

 

portfast:

 Shows if Port Fast Forwarding is enabled or disabled.  

•

 

tagging:

 Shows if this port has VLAN Tagging enabled or disabled. 

•

 

PVID:

 VLAN ID of any VLAN(s) to which this port is a member. 

Operational Status 

Displays the operational status of the port. 

Speed/Duplex/Flow Ctl 

Displays parameters for the port link. 

Input Frames/Output Frames 

Displays the number of frames that have been received by this port (Input 
Frames) and the number of frames that have been transmitted by this port 

(Output Frames). 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

D-Link D DPH-50U DPH-50U Product Data Sheet preview
D DPH-50U DPH-50U
Brand: D-Link Pages: 2
D-Link AirPlus DWL-810 User Manual preview
AirPlus DWL-810
Brand: D-Link Pages: 64
D-Link Air DWL-120 Manual preview
Air DWL-120
Brand: D-Link Pages: 39
D-Link AC600 MU-MIMO Quick Install Manual preview
AC600 MU-MIMO
Brand: D-Link Pages: 8
D-Link 802.11g Wireless LAN USB Adapter DWL-G122 Manual preview
802.11g Wireless LAN USB Adapter DWL-G122
Brand: D-Link Pages: 43
D-Link AirPlusXtremeG DWL-G650 Manual preview
AirPlusXtremeG DWL-G650
Brand: D-Link Pages: 20
Daikin BRP069A71 Installation Manual preview
BRP069A71
Brand: Daikin Pages: 8
Daikin BRP069A61 Installer'S Reference Manual preview
BRP069A61
Brand: Daikin Pages: 16
Parker IQAN-G12 Instruction Book preview
IQAN-G12
Brand: Parker Pages: 36
Dynex DX-TADPT1 Quick Setup Manual preview
DX-TADPT1
Brand: Dynex Pages: 2
Amedia DMA 3.1L User Manual preview
DMA 3.1L
Brand: Amedia Pages: 8
Qlogic SANblade 2300 Series Quick Start Manual preview
SANblade 2300 Series
Brand: Qlogic Pages: 12
R&S ENY21 Operating Manual preview
ENY21
Brand: R&S Pages: 66
Adaptec 1890600 Hardware Installation Manual preview
1890600
Brand: Adaptec Pages: 12
EtherWAN GE3000 User Manual preview
GE3000
Brand: EtherWAN Pages: 21
Conceptronic CPNP200 Quick Installation Manual preview
CPNP200
Brand: Conceptronic Pages: 209
Linksys Linksys SPA9000 Administration Manual preview
Linksys SPA9000
Brand: Linksys Pages: 246
HP Z Series User Manual preview
Z Series
Brand: HP Pages: 40

Brands by name

Popular brands

Load more brands