manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

232

 

VRRP Interface Configuration 

To display the following form, go to the Virtual Routers Configuration form. Select a VRRP interface 
number or open the VRRP Interfaces folder and click 

Add Virtual router Interface.

   

 

The following table describes the VRRP Interface Configuration controls: 

Table 166 

 VRRP Interface Configuration controls 

 

Control Descriptions 

IP Interface (1-256) 

Defines the IP interface. 

Authentication? 

Defines the type of authentication that will be used: none (no authentication), or 
password (password authentication). 

Password 

Defines a plain text password up to eight characters long. This password will be 

added to each VRRP packet transmitted by this interface when password 

authentication is chosen (see Authentication above). 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Rotel RDA 980 Owner'S Manual preview
RDA 980
Brand: Rotel Pages: 8
Exsys EX-6605E Manual preview
EX-6605E
Brand: Exsys Pages: 2
VOLTCRAFT 51 42 02 Operating Instructions Manual preview
51 42 02
Brand: VOLTCRAFT Pages: 8
Citel Portico TVA Series Installation And Configuration Manual preview
Portico TVA Series
Brand: Citel Pages: 109
Conrad 87 23 00 Operating Instructions preview
87 23 00
Brand: Conrad Pages: 2
NCR 7707-K125 Kit Instructions preview
7707-K125
Brand: NCR Pages: 16
NCR 7360-K502 Kit Instructions preview
7360-K502
Brand: NCR Pages: 38
HP P9000 Software Installation Manual preview
P9000
Brand: HP Pages: 128
Askey WLL3041 User Manual preview
WLL3041
Brand: Askey Pages: 60
OBDLink MX Wi-Fi Quick Start Manual preview
MX Wi-Fi
Brand: OBDLink Pages: 12
weintek iR-ETN User Manual preview
iR-ETN
Brand: weintek Pages: 37
SMC Networks SMC2336W-AG Specifications preview
SMC2336W-AG
Brand: SMC Networks Pages: 2
SMC Networks WiShare SMCWTVA100 User Manual preview
WiShare SMCWTVA100
Brand: SMC Networks Pages: 81
SMC Networks EZ Connect SMCWUSBS-N3 Specifiations preview
EZ Connect SMCWUSBS-N3
Brand: SMC Networks Pages: 2
SMC Networks EZ Connect SMCWUSB-G Manual preview
EZ Connect SMCWUSB-G
Brand: SMC Networks Pages: 54
SMC Networks EZ Connect SMC2435W Datasheet preview
EZ Connect SMC2435W
Brand: SMC Networks Pages: 2
SMC Networks 2835W Quick Installation Manual preview
2835W
Brand: SMC Networks Pages: 44
SMC Networks 10GPCIE-10BT FICHE Specification Sheet preview
10GPCIE-10BT FICHE
Brand: SMC Networks Pages: 2

Brands by name

Popular brands

Load more brands