manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

225

 

RIP Interface Configuration 

To display the following form, go to the RIP Interfaces Configuration form. Select a RIP interface number, 
or open the RIP Interfaces folder and click 

Add RIP Interface. 

  

 

The following table describes the RIP Interface Configuration controls: 

Table 160 

 RIP Interface Configuration controls 

 

Control Descriptions 

IP Interface number (1-255) 

Assigns a numeric identifier to the RIP interface. 

Enable RIP? 

Enables or disables the RIP interface. 

RIP Version 

Configures the RIP version used by this interface. The default value is version 1. 

Default Route Action 

When enabled, the switch accepts RIP default routes from other routers, but gives 
them lower priority than configured default gateways. When disabled, the switch 

rejects RIP default routes. The default value is disabled. 

Supply Route Updates? 

When enabled, the switch supplies routes to other routers. The default value is 

disabled. 

Listen to Route Updates? 

When enabled, the switch learns routes from other routers. The default value is 
disabled. 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

3idee hp-32f Assembly Instructions Manual preview
hp-32f
Brand: 3idee Pages: 7
IBM Flex System EN4132 Product Manual preview
Flex System EN4132
Brand: IBM Pages: 11
Bose SoundTouch 120 Quick Start Manual preview
SoundTouch 120
Brand: Bose Pages: 2
Davis Instruments Coupler Kit Install Manual preview
Coupler Kit
Brand: Davis Instruments Pages: 4
VENOM PRO ALL-IN-ONE Instruction Manual preview
PRO ALL-IN-ONE
Brand: VENOM Pages: 2
Keysight Technologies E2613A User Manual preview
E2613A
Brand: Keysight Technologies Pages: 24
AVM FRITZ!Powerline 510E Set Installation And Operation Manual preview
FRITZ!Powerline 510E Set
Brand: AVM Pages: 38
Belkin F5U514 User Manual preview
F5U514
Brand: Belkin Pages: 38
Belkin F5D8073 User Manual preview
F5D8073
Brand: Belkin Pages: 44
Steren Com-878 User Manual preview
Com-878
Brand: Steren Pages: 45
Compaq NC3134 User Manual preview
NC3134
Brand: Compaq Pages: 33
Cortelco FOUR LINE CORDLESS ANALOG ADAPTER 2742 Owner'S Instruction Manual preview
FOUR LINE CORDLESS ANALOG ADAPTER 2742
Brand: Cortelco Pages: 21
EnGenius EUB-3701 EXT User Manual preview
EUB-3701 EXT
Brand: EnGenius Pages: 32
Compex WLU108G Quick Installation Manual preview
WLU108G
Brand: Compex Pages: 22
Spectrum 24 LA-4111 Quick Reference Manual preview
LA-4111
Brand: Spectrum 24 Pages: 2
ConnectGear WU240G User Manual preview
WU240G
Brand: ConnectGear Pages: 30
Gigafast EE100-AEP Installation Manual preview
EE100-AEP
Brand: Gigafast Pages: 12
RCA AH765R User Manual preview
AH765R
Brand: RCA Pages: 2

Brands by name

Popular brands

Load more brands