manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

Share
Download
HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download Page 240

 

 

 

Configuring the switch

 

 

 

  

 

240

 

QoS Switch Port Configuration 

To display the following form, go to the Switch Port Priority Configuration table, and select a port number.  

 

The following table describes the QoS switch port priority configuration controls:  

Table 173 

 QoS Switch Port Priority Configuration controls 

 

Control Description 

Port Priority (0-7) 

Configures the 802.1p priority value for the port.  

 

QoS Number of CoS Configuration 

To display the following form, select 

QoS > 802.1p > Number of CoS.

 

 

The following table describes the QoS switch port priority configuration controls:  

Table 174 

 QoS Switch Port Priority Configuration controls 

 

Control Description 

Number of CoS (2, 8) 

Sets the number of Class of Service queues for switch ports.  
The default value is 2.  

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands