manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

Share
Download
HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download Page 222

 

 

 

Configuring the switch

 

 

 

  

 

222

 

OSPF Host Configuration 

To display the following form, go to the OSPF Hosts Configuration form. Select a host number, or open 
the OSPF Hosts folder and click 

Add OSPF Host.

  

 

The following table describes the OSPF Host Configuration controls: 

Table 157 

 OSPF Host Configuration controls 

 

Control Descriptions 

Host Identifier (1-128) 

Assigns a numeric identifier to the OSPF host. 

IP Address 

Defines the base IP address for the host entry. 

Enabled? 

Enables or disables the OSPF virtual link. 

Area Number (0-2) 

Defines the area index used by the OSPF host. 

Output Cost (1-65535) 

Defines the cost value of the host. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands