manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

Share
Download
HP 438031-B21 - 1:10Gb Ethernet BL-c Switch Reference Manual Download Page 185

 

 

 

Configuring the switch

 

 

 

  

 

185

 

Uplink Fast General Configuration 

To display the following form, select 

Layer 2 > UpLink Fast.

 

 

The following table describes the Uplink Fast Configuration controls: 

Table 126 

 Uplink Fast Configuration controls 

 

Control Description 

Enabled? 

Enables or disables Fast Uplink Convergence, which provides rapid Spanning Tree 
convergence to an upstream switch during failover.  

NOTE: 

 When enabled, this feature increases bridge priorities to 65500 for all 

STGs and path cost by 3000 for all external STP ports. 

Update Rate (10-200) 

Configures the station update rate. The default value is 40. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands