manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

194

 

IP Interface Configuration 

To display the following form, go to the IP Interfaces Configuration form. Select an IP Interface number, or 
open the IP Interfaces folder and click 

Add IP Interface.

 

 

The switch can be configured with up to 256 IP interfaces. Each IP interface represents the switch on an IP 

subnet on your network. The Interface option is disabled by default. 
The following table describes the IP Interface Configuration controls: 

Table 134 

 IP Interface Configuration controls 

 

Control Description 

IP Interface Identifier (1-256) 

Selects an IP interface to configure. 

IP Address 

Configures the IP address of the switch interface using dotted decimal notation. 

Enabled? 

Enables or disables this IP interface. 

Subnet Mask 

Configures the IP subnet address mask for the interface using dotted decimal 

notation. 

VLAN Membership ID (1-4095)  Configures the VLAN number for this interface. Each interface can belong to one 

VLAN, although any VLAN can have multiple IP interfaces in it. 

Enable/Disable BOOTP Relay 

Enables or disables the BOOTP relay on this interface. The default value is 

enabled

. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

quadient iX-1 Series Replacement Manual preview
iX-1 Series
Brand: quadient Pages: 2
SWEEX BT202 User Manual preview
BT202
Brand: SWEEX Pages: 3
D-Link DWA-162 Quick Install Manual preview
DWA-162
Brand: D-Link Pages: 1
Atlona USB202 VIDEO/AUDIO TO USB 2.0 ADAPTOR User Manual preview
USB202 VIDEO/AUDIO TO USB 2.0 ADAPTOR
Brand: Atlona Pages: 26
TRENDnet TBW-105UB User Manual preview
TBW-105UB
Brand: TRENDnet Pages: 40
Daikin DCM601A72 Installation Manual preview
DCM601A72
Brand: Daikin Pages: 36
Digitus DA-70833 User Manual preview
DA-70833
Brand: Digitus Pages: 34
Monster JHIU0109 Quick Manual preview
JHIU0109
Brand: Monster Pages: 2
Black Box IC138A-R2 Manual preview
IC138A-R2
Brand: Black Box Pages: 20
AccuPower AP1222-1 User Manual preview
AP1222-1
Brand: AccuPower Pages: 9
LSILogik eXtreemeRAID 3000 Quick Installation Manual preview
eXtreemeRAID 3000
Brand: LSILogik Pages: 24
RDZ Kit WI - Knx 2.0 Installation Manual preview
Kit WI - Knx 2.0
Brand: RDZ Pages: 36
NETGEAR XAVB5501 Installation Manual preview
XAVB5501
Brand: NETGEAR Pages: 2
weintek iR-ETN User Manual preview
iR-ETN
Brand: weintek Pages: 37
Corinex PoerNet Owner'S Manual preview
PoerNet
Brand: Corinex Pages: 26
Compaq ESA12000 User Manual preview
ESA12000
Brand: Compaq Pages: 167
Dynalink ISDN Quick Start Manual preview
ISDN
Brand: Dynalink Pages: 110
Paradyne 6512-A2 Installation Instructions Manual preview
6512-A2
Brand: Paradyne Pages: 36

Brands by name

Popular brands

Load more brands