manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

208

 

IGMP Filter Configuration 

To display the following form, go to the IGMP Filters Configuration form. Select a Filter ID, or open the 
IGMP Filters folder and click 

Add Filter.

 

 

The following table describes the IGMP Filter Configuration controls: 

Table 146 

 IGMP Filter Configuration controls 

 

Control Description 

Filter Identifier (1 - 16) 

Selects an IGMP filter to configure. 

Enabled? 

Enables or disables this IGMP filter. 

Range 1 IP Multicast Address 

Configures the start of the range of IP multicast addresses for this filter. 

Range 2 IP Multicast Address 

Configures the end of the range of IP multicast addresses for this filter. 

Action 

Allows or denies multicast traffic for the IP multicast address range specified. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

NETGEAR PowerLINE PLW1000v2 Quick Start Manual preview
PowerLINE PLW1000v2
Brand: NETGEAR Pages: 16
Tele System P-Link 0.3 WiFi Kit User Manual preview
P-Link 0.3 WiFi Kit
Brand: Tele System Pages: 24
TP-Link TL-PA201 STARTER Specifications preview
TL-PA201 STARTER
Brand: TP-Link Pages: 2
Future Domain TMC-8S0M User Manual preview
TMC-8S0M
Brand: Future Domain Pages: 48
Ampetronic ATT100-T42 Manual preview
ATT100-T42
Brand: Ampetronic Pages: 2
Zoom 1054 Series Quick Start Manual preview
1054 Series
Brand: Zoom Pages: 8
Sinapsi EQUOBOX SIN.EQLC250 User Manual preview
EQUOBOX SIN.EQLC250
Brand: Sinapsi Pages: 14
Sveon SNT1010 User Manual preview
SNT1010
Brand: Sveon Pages: 19
LevelOne WUA-1810E User Manual preview
WUA-1810E
Brand: LevelOne Pages: 30
Moeller Xcomfort CSAP-01/0 Series Assembly Instructions preview
Xcomfort CSAP-01/0 Series
Brand: Moeller Pages: 4
ResMed Astral 150 Information And User Manual For Qualified Professionals preview
Astral 150
Brand: ResMed Pages: 31
Proware M-WN910N User Manual preview
M-WN910N
Brand: Proware Pages: 39
Flying Voice FTA1101 User Manual preview
FTA1101
Brand: Flying Voice Pages: 46
Kvaser 73-30130-01261-5 User Manual preview
73-30130-01261-5
Brand: Kvaser Pages: 25
Tripp Lite U244-001-HDMI-R Owner'S Manual preview
U244-001-HDMI-R
Brand: Tripp Lite Pages: 12
ProTek R/C TruGlow Instruction Manual preview
TruGlow
Brand: ProTek R/C Pages: 2
Sony BKM-20D Notes On Usage preview
BKM-20D
Brand: Sony Pages: 2
Sony BDV-HZ970W (UWA-BR100) Speaker Installation Manual preview
BDV-HZ970W (UWA-BR100)
Brand: Sony Pages: 2

Brands by name

Popular brands

Load more brands