manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

144

 

User Access Control Configuration 

To display the following form, go to the User Configuration Table and click 

Add User.

  

 

The following table describes User Access Configuration controls:  

Table 98 

 User Access Configuration controls 

 

Control Description 

User ID (1-10) 

Sets a numeric identifier for the user. 

Set Class of Service 

Sets the Class-of-Service to define the user’s authority level. 

Set user name (0-8 chars) 

Defines the user name of maximum eight characters. 

Set user password (0-128 chars) 

Sets the user password of up to 128 characters maximum. 

Re-type user password (0-128 chars) 

Confirms the user password. 

User Status 

Enables or disables the user. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Sabrent TH-3HD2 User Manual preview
TH-3HD2
Brand: Sabrent Pages: 4
Renesas PCA4738F-100A User Manual preview
PCA4738F-100A
Brand: Renesas Pages: 26
TRENDnet TEW-226PC Quick Installation Manual preview
TEW-226PC
Brand: TRENDnet Pages: 11
SMC Networks EZ Connect N SMCWUSBS-N User Manual preview
EZ Connect N SMCWUSBS-N
Brand: SMC Networks Pages: 64
Roche ACCU-CHECK Instructions For Use preview
ACCU-CHECK
Brand: Roche Pages: 2
Belkin ExpressCard N User Manual preview
ExpressCard N
Brand: Belkin Pages: 58
NETGEAR WAB501 - 802.11a/b Dual Band PC Card User Manual preview
WAB501 - 802.11a/b Dual Band PC Card
Brand: NETGEAR Pages: 17
TP-Link TL-PA211 Quick Installation Manual preview
TL-PA211
Brand: TP-Link Pages: 75
insys icom ISDN TA 4.0 Manual preview
ISDN TA 4.0
Brand: insys icom Pages: 100
TDK HHM Series HHM2208SB1 Specifications preview
HHM Series HHM2208SB1
Brand: TDK Pages: 2
Curtis Computer AP1075 Instructions preview
AP1075
Brand: Curtis Computer Pages: 2
Philips SNN6600 User Manual preview
SNN6600
Brand: Philips Pages: 25
Asante AsanteFAST 100 User Manual preview
AsanteFAST 100
Brand: Asante Pages: 74
G-Trend FB1310 User Manual preview
FB1310
Brand: G-Trend Pages: 17
IBM Redbooks ServeRAID-MR10k Quick Install Manual preview
Redbooks ServeRAID-MR10k
Brand: IBM Pages: 3
IBM ThinkPad 600 Software Manual preview
ThinkPad 600
Brand: IBM Pages: 35
IBM 37L1415 Installation Manual preview
37L1415
Brand: IBM Pages: 18
IBM System Storage DS4000 Installation And User Manual preview
System Storage DS4000
Brand: IBM Pages: 84

Brands by name

Popular brands

Load more brands