manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Viewing statistics

 

 

 

  

 

130

 

The following table describes the Address Resolution Protocol (ARP) statistics:  

Table 90 

 ARP statistics 

 

Statistics Description 

Current Entries 

The total number of outstanding ARP entries in the ARP table.  

High Water Mark 

The highest number of ARP entries ever recorded in the ARP table.  

Maximum Entries 

The maximum number of ARP entries that are supported.  

 

IP Routing Management Statistics (part 2) 

To display the following form, select 

Layer 3 > Network Routes 

(click the underlined text, not the 

folder). 

 

The following table describes the Internet Control Messaging Protocol (ICMP) statistics:  

Table 91 

 ICMP statistics 

 

Statistics Description 

icmpInMsgs 

The total number of ICMP messages which the switch received. Note that this 
counter includes all those counted by icmpInErrors. 

icmpInErrors 

The number of ICMP messages which the switch received but determined as having 

ICMP specific errors (for example bad ICMP checksums and bad length). 

icmpInDestUnreachs 

The number of ICMP Destination Unreachable messages received. 

icmpInTimeExcds 

The number of ICMP Time Exceeded messages received. 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Tamio U1 Quick Installation Manual preview
U1
Brand: Tamio Pages: 2
Qlogic QLE3142-SR-CK Quick Start Manual preview
QLE3142-SR-CK
Brand: Qlogic Pages: 8
Linksys WUSBF54G Quick Installation Manual preview
WUSBF54G
Brand: Linksys Pages: 2
ZyXEL Communications ZyXEL ZyAIR B-400 User Manual preview
ZyXEL ZyAIR B-400
Brand: ZyXEL Communications Pages: 31
Hainbuch MANOK Plus Operating Instructions Manual preview
MANOK Plus
Brand: Hainbuch Pages: 108
Adaptec 1890600 Hardware Installation Manual preview
1890600
Brand: Adaptec Pages: 12
Nvidia MCX4121A-ACAT User Manual preview
MCX4121A-ACAT
Brand: Nvidia Pages: 62
Digitus DA-70833 User Manual preview
DA-70833
Brand: Digitus Pages: 34
Kvaser BlackBird v2 User Manual preview
BlackBird v2
Brand: Kvaser Pages: 21
MSG Equipment MSG MS013 COM User Manual preview
MSG MS013 COM
Brand: MSG Equipment Pages: 12
RocketFish RF-PCC132 (French) Manual D'Installation Rapide preview
RF-PCC132
Brand: RocketFish Pages: 2
HP 381513-B21 - Smart Array P800 Controller RAID User Manual preview
381513-B21 - Smart Array P800 Controller RAID
Brand: HP Pages: 55
D-Link DUB-2332 Quick Installation Manual preview
DUB-2332
Brand: D-Link Pages: 7
D-Link DVG-5102S User Manual preview
DVG-5102S
Brand: D-Link Pages: 30
D-Link DUB-1210 User Manual preview
DUB-1210
Brand: D-Link Pages: 25
D-Link DUB-9240 - UWB Wireless USB Installation Manual preview
DUB-9240 - UWB Wireless USB
Brand: D-Link Pages: 16
D-Link DUB-1310 User Manual preview
DUB-1310
Brand: D-Link Pages: 17
D-Link DUB-2240 - Wireless USB Hub User Manual preview
DUB-2240 - Wireless USB Hub
Brand: D-Link Pages: 16

Brands by name

Popular brands

Load more brands