manualshive.com logo in svg

HP 438031-B21 - 1:10Gb Ethernet BL-c Switch, Reference Manual

The HP 438031-B21 - 1:10Gb Ethernet BL-c Switch is a versatile networking device that offers reliable and high-speed connectivity. To fully take advantage of its features, make sure to download the comprehensive Command Reference Manual from our website manualshive.com for free. This manual provides detailed instructions and troubleshooting tips to optimize your experience with this product.

Share
Download
background image

 

 

 

Configuring the switch

 

 

 

  

 

201

 

Route Map Configuration 

To display the following form, go to the Route Maps Configuration form. Select a route map ID number, 
or open the Route Maps folder and click 

Add Route Map.

 

 

The following table describes the Route Map Configuration controls: 

Table 141 

 Route Map Configuration controls 

 

Control Description 

Route Map Identifier (1-32) 

Assigns a numeric identifier to the route map. 

Local Preference (1-4294967294 | 
none=4294967295) 

Sets the local preference of the matched route, which affects 
both inbound and outbound directions. The path with the higher 

preference is preferred. 

Precedence (1-255) 

Sets the precedence of the route map. The smaller the value, the 

higher the precedence. Default value is 10. 

AS-Path Prepend of the Matched Route 

Sets the AS path preference of the matched route. One to three 
path preferences can be configured. 

Metric (1-4294967294 | none=4294967295) 

Sets the metric of the matched route. 

Weight (0-65534 | none=65535) 

Sets the weight of the route map. 

Enabled? 

Enables or disables the route map. 

 

Summary of Contents for 438031-B21 - 1:10Gb Ethernet BL-c Switch





























































































































































































































































Reviews:

No comments

Related manuals for 438031-B21 - 1:10Gb Ethernet BL-c Switch

Elnec 70-0903 Quick Start Manual preview
70-0903
Brand: Elnec Pages: 2
Patton electronics 14TB User Manual preview
14TB
Brand: Patton electronics Pages: 2
Proyecson PAA20+ Installation Manual preview
PAA20+
Brand: Proyecson Pages: 148
Digitus DA-70148-3 User Manual preview
DA-70148-3
Brand: Digitus Pages: 10
Hainbuch MANOK Plus Operating Instructions Manual preview
MANOK Plus
Brand: Hainbuch Pages: 108
Digitus DN-70031 Quick Start Manual preview
DN-70031
Brand: Digitus Pages: 6
Intermec CN3 Series Quick Start Manual preview
CN3 Series
Brand: Intermec Pages: 12
Keyspan Mini Port Replicator User Manual preview
Mini Port Replicator
Brand: Keyspan Pages: 41
Supermicro AOC-A100G-b2CM User Manual preview
AOC-A100G-b2CM
Brand: Supermicro Pages: 27
J-Three BU-2061-J Quick Installation Manual preview
BU-2061-J
Brand: J-Three Pages: 10
Tailwind iQ3-LM User Manual preview
iQ3-LM
Brand: Tailwind Pages: 3
Philips PowerLife 3LR12P1B Brochure preview
PowerLife 3LR12P1B
Brand: Philips Pages: 2
Philips LightMaster PLC-KNX Installation Manual preview
LightMaster PLC-KNX
Brand: Philips Pages: 2
Philips Home Power SPS3102WB/37 User Manual preview
Home Power SPS3102WB/37
Brand: Philips Pages: 2
Philips LIGHTOLIER IS-LLAH11 Manual preview
LIGHTOLIER IS-LLAH11
Brand: Philips Pages: 4
Asante FriendlyNET 595 Adapter User Manual preview
FriendlyNET 595 Adapter
Brand: Asante Pages: 2
SWEEX BT214 Installation preview
BT214
Brand: SWEEX Pages: 4
Well Comfy Installation And Operating Manual preview
Comfy
Brand: Well Pages: 7

Brands by name

Popular brands

Load more brands