114
Dopo la verifica, premere il pulsante per ritornare alla modalità di funzionamento normale, proseguire quindi
con un’altra operazione, altrimenti il tasto NIBP non sarà valido.
La verifica dell’accuratezza della pressione deve essere eseguita da un tecnico autorizzato. L’esecuzione
della verifica non è consentita a personale medico o infermieristico, a causa della pericolosità dell’opera-
zione, in particolare quando il bracciale per la misurazione della pressione è ancora in uso sul paziente.
�
Verifica di perdite d’aria
Al fine di evitare errori rilevanti o l’assenza di risultati nella misurazione della pressione sanguigna a causa di
perdite d’aria, si raccomanda di verificare la presenza di perdite nel sistema pneumatico, bracciale compreso.
Quando si esegue la verifica delle perdite, rimuovere il bracciale dal paziente.
24.5 Calibrazione IBP (Opzionale)
Questa sezione è destinata a personale tecnico professionista.
Ogni volta che si collega il trasduttore o che si seleziona una misura alternativa di calibrazione, un messaggio
di prompt compare sullo schermo. Sono possibili due metodi di calibrazione: calibrazione a zero e calibrazione
del valore di pressione.
Procedure della calibrazione:
1. Nella finestra di calibrazione, premere il pulsante “Zero” per effettuare una calibrazione a zero, quindi “Ze-
roing OK” (Azzeramento effettuato) verrà mostrato nella finestra.
I seguenti messaggi potrebbero apparire nella finestra durante la calibrazione:
• Sonda disattivata, impossibile azzerare
• Sonda disattivata, pressione di riferimento a zero
• Pressione di riferimento a zero instabile
• Pressione oltre i limiti
• Azzeramento OK
2. Espellere tutta l’aria dai tubi, quindi regolare il tubo di trasfusione e il rubinetto di arresto (“Off” al tubo di
trasfusione). Aprire il tappo antipolvere, e assicurarsi che la calotta sia a contatto con l’aria.
3. Se è necessaria la calibrazione a zero, questa deve essere eseguita prima del monitoraggio IBP, altrimenti
le letture IBP potrebbero essere imprecise.
4. Si raccomanda che la “0 calibration” (Calibrazione a 0) venga eseguita prima della misurazione, ed effet-
tuata almeno una volta a giorno (la calibrazione a zero deve essere eseguita ogni volta che la presa viene
connessa alla presa IBP del monitor), o l’accuratezza della misurazione ne risulterà compromessa. Eseguire
la calibrazione della pressione se si utilizza un trasduttore IBP nuovo.
24.6 Test CO
2
Per i moduli CO
2
sidestream, è necessario eseguire la calibrazione ogni anno nel caso in cui i risultati mostrino
una deviazione rilevante. Per i moduli CO
2
mainstream non è necessaria alcuna calibrazione. Per effettuare la
calibrazione CO
2
, contattare il personale di servizio.
24.7 Calibrazione AG
Calibrare il modulo AG ogni anno o nel caso in cui il valore misurato mostri una deviazione rilevante. Per effet-
tuare la calibrazione AG, contattare il personale di servizio.
Summary of Contents for 35145
