Foma N903i, Manual

Page: 59 / 580

57
Voice/Videophone Calls
Changing a Call Between Voice and Videophone
d
You can only change the call mode when you are the caller. When you are a callee, you cannot change the
call mode.
d
To change the call mode, the other party must set his or her terminal to show you “Ntfy switch-mode”
beforehand.
→ p.89
d
You can repeatedly change the call mode between voice and videophone.
d
Changing a call from voice to videophone
You can change the call mode during a voice call you dialed.
d
If the other party uses a FOMA terminal that can change the call mode, “ ” appears during a voice
call and you can change the call mode between voice and videophone. (This function is available between
terminals that support change between voice call and videophone call.)
1
In-call screen
X
d
( )
X
“YES”
While a voice call is being changed to a videophone call, the screen showing that the call mode is being
changed appears and the voice guidance is given.
Select “NO” on the “Ntfy switch-mode” message screen to return to the in-call screen.
e
The “32K” connection speed allows you to use videophone with other devices (PHS mobiles, etc.) that cannot
communicate at “64K” due to network conditions. If you make a videophone call at “64K” and the called party is in a
“32K” area or similar situation, the call is automatically redialed at 32kbps. However, note that “32K” videophone
calls attract the same digital communication charges as “64K” videophone calls.
e If “Auto redial as voice” (p.86) is set to “ON” and a videophone call is not connected, the call is automatically
changed to a voice call. The relations between the set connection speed and “Auto redial as voice” setting are
listed below.
e
You cannot receive i-mode mails, MessageR or MessageF during a videophone call. Mails you cannot receive are
held at the i-mode Center. Receive them using “Check new messages” after the videophone call ends.
e
You can receive SMS during a videophone call.
e
If the “Recharge battery” low voltage alarm appears on the display during a videophone call, the other party sees
the “
カメラオフ
Camera Off” message and the call is disconnected roughly 20 seconds later. If you start charging
a battery before a videophone call is terminated, the call continues with the image that had been displayed before
the low voltage alarm was given.
e
Digital call charges still apply when a substitute image appears during a videophone call.
“Auto redial as
voice” set to ON The connection speed automatically changes to
“32K”. If the videophone call still fails to connect, it
switches to voice-call mode. Switches to voice call mode.
“Auto redial as
voice” set to OFF The connection speed automatically changes to
“32K”. If the videophone call still fails to connect,
the videophone call ends. Ends the videophone call.
Dialing speed set to “64K” Dialing speed set to “32K”
Ｖ．ｐｈｏｎｅ
Ｖ．ｐｈｏｎｅ
［Ｔａｌｋｉｎｇ］
１ｍ３０ｓ
１０ｓ ４ｓ
［通話中］
１ｍ３０ｓ ＹＥＳ
ＮＯ
Ｎｔｆｙ ｓｗｉｔｃｈ−ｍｏｄｅ
Ｃｈａｎｇｉｎｇ？
Ｖｉｄｅｏｐｈｏｎｅ
［Ｃｈａｎｇｉｎｇ］
［Ｃｈａｎｇｉｎｇ］
The digital communication
fee is charged after the
appearance of this screen.