Foma N903i, Manual

Page: 563 / 580

46
AT ＊ DANTE Displays the FOMA
terminal signal reception
level.
0
：
FOMA terminal signal reception level is displayed
as out of area.
1 ： FOMA terminal signal reception level is 0 or 1
bar.
2
：
FOMA terminal signal reception level is 2 bars.
3
：
FOMA terminal signal reception level is 3 bars.
AT ＊ DANTE
＊
DANTE:3
OK
AT ＊ DANTE ＝ ?
＊ DANTE:(0-3)
OK
AT ＊ DGANSM=
n
Sets the reject/permit mode
setting for the packet
incoming call. This
command is effective for
those incoming packet calls
after the setting command
is input.
n = 0 ： Disables the incoming call reject (AT ＊
DGARL)/permit setting (AT ＊ DGAPL)
(initial value).
n = 1 ： Enables the incoming call reject
setting.
n = 2 ： Enables the incoming call permit
setting.
AT ＊ DGANSM?
： Displays the current setting.
AT ＊ DGANSM=0
OK
AT
＊
DGANSM?
＊ DGANSM:0
OK
AT
＊
DGAPL=
n
[,cid]
Sets APN, which permits
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT n
= 0
：
Adds the APN defined by <cid> to
incoming call permission list.
n
= 1 : Deletes the APN defined by <cid>
from incoming call permission list.
If <cid> is omitted, this will apply to all cid.
AT
＊
DGAPL?
：
Displays incoming call permission
list.
AT
＊
DGAPL =0,1
OK
AT
＊ DGAPL?
＊ DGAPL:1
OK
AT
＊ DGAPL =1
OK
AT
＊ DGAPL?
OK
AT ＊ DGARL= n [,cid] Sets APN, which rejects
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
n
= 0 : Adds the APN defined by <cid> to
incoming call rejection list.
n
= 1 : Deletes the APN defined by <cid>
from incoming call rejection list.
If <cid> is omitted, this will apply to all cid.
AT
＊ DGARL?
： Displays incoming call rejection list.
AT ＊ DGARL =0,1
OK
AT
＊
DGARL?
＊ DGARL:1
OK
AT
＊ DGARL =1
OK
AT
＊ DGARL?
OK
AT
＊
DGPIR=
n
This command validates
the setting for notifying
Caller ID when sending/
receiving packet
communication.
Even in the dial up network
setting, you can also add
186 (notify) or 184 (not
notify) to the access point
number. (p.35)
n
= 0 : Uses APN as it is (initial value).
n
= 1 : Uses APN by adding “184”. (Caller ID
is always not sent.)
n
= 2 : Uses APN by adding “186”. (Caller ID
is always sent.)
AT
＊
DGPIR?
：
Displays the current setting.
AT
＊
DGPIR =0
OK
AT
＊ DGPIR?
＊ DGPIR:0
OK
AT ＊ DRPW Displays the indicator value
of the receiving power of
the FOMA terminal.
−
AT ＊ DRPW
＊
DRPW:0
OK
AT ＊ DRPW=?
＊ DRPW:(0-75)
OK
AT+CAOC Inquires for the current
charge.
−
AT+CAOC
+CAOC:“000014”
OK
AT+CBC Displays the battery status
of the FOMA terminal. Result: +CBC:<bcs>,<bcl>
bcs:
0 : FOMA terminal is powered by the
battery.
1 : FOMA terminal is not powered by the
battery.
2 : FOMA terminal is not connected to the
battery.
3 : FOMA terminal is out of transmission
due to the power-supply error.
bcl:
0 : Battery has run out, or battery is not
connected.
1-100 : Battery remained
AT+CBC
+CBC:0,70
OK
AT+CBC?
ERROR
AT+CBC=?
+CBC:(0-3),(0-100)
OK
AT command Outline Parameter/description Command execution example