Foma N903i, Manual

Page: 482 / 580

480
Appendix/External Devices/Troubleshooting
“Caution! This SMS includes
Phone Nos. or URLs. Be careful if
you do not recognize the sender.”
d
This message appears when “Message scan” under “Scanning
function” is set to “ON” and try to display a SMS contained phone
number or URL in the message. Press
d
if you want to display a
SMS message after checking its source.
p.492
“Certificate is rejected
(tampered)”
d
This message appears when an altered SSL certificate has been
received. An SSL communication cannot be established with this site.
d
This message appears when an altered TLS/SSL certificate has been
received. A TLS/SSL communication cannot be established with this site.
−
“Check new messages is set all
OFF” d New messages cannot be checked because none of the items is
selected in “Set check new messages”.
Select items to check in “Set check new messages”. p.271
“Connection failed (403)”
d
The attempt to access a site has failed for some reason. Retry
connection.
−
“Connection failed”
d
Set “Caller ID Notification” to “ON” and retry. p.50
“Connection failed”
d
This message appears when the host setting is not correct. Set the
host correctly in “Host selection” under Connection setting.
d
The attempt to connect to i-mode has failed for some reason. Retry
connection.
p.224
−
“Connection interrupted” d i-mode connection was interrupted due to poor reception. Move to a
location where the reception is good before using the i-mode service.
d
If this message appears even when the reception is good and
“ ” appears, the site you are accessing is busy. Retry later.
p.208
−
“Continue using i-
α
ppli and
transmit data?”
d
This message appears when you select “NO” or “Terminate i-
α
ppli”
in response to the message “Data transmission is frequent Continue
transmission?”. Select “YES” to continue i-
α
ppli communication. To
quit using an i-
α
ppli program, select “Terminate i-
α
ppli”.
−
“Could not read”
d
The data cannot be copied due to some error. Exchange with a new
microSD memory card then retry to copy.
−
“Data in IC-card is full
Unable to download
Delete service?”
“Data in IC-card is full
Unable to run
Delete service?”
“Data in IC-card is full
Unable to upgrade
Delete service?”
d
This message appears when you attempt to download Osaifu-Keitai
i-
α
ppli but the space is not enough on the IC card. Select “YES” to
display already registered Osaifu-Keitai services, space (bytes)
allocated by removing the service, and necessary area size. Select a
service to remove, follow the message and launch i-
α
ppli to remove
the service.
−
“Data is too long A part is deleted”
d
The size of address, subject or text or more than one data exceeds
the maximum, and the Compose message screen appears with the
excess part deleted.
−
“Data is too long Please delete
message” d The total length of the message text and quotation mark characters
in the i-mode message to be quoted in a reply exceeds 5,000
double-byte characters. Delete some of the text to reduce the
character count to 5,000 double-byte characters or fewer.
−
“Data transmission is frequent
Continue transmission?”
d
This message appears when the number of communications that are
using i-
α
ppli and have been established in a given time is extremely
large. Select “YES” to continue to make i-
α
ppli communication, or
“NO” to quit the communication. To quit using an i-
α
ppli program,
select “Terminate i-
α
ppli”.
−
“Data transmission is frequent
Press CLR and confirm data
transmission” d This message appears when the number of communications
established from the i-
α
ppli standby screen in a given time is extremely
large. Press
t
to select whether to permit communication from the
i-
α
ppli standby screen or whether to exit the i-
α
ppli standby screen.
p.294
“Dial/Receive calls activating
Original lock”
d
This message appears when you attempt to perform a prohibited operation
in Original lock set to “Dial/sending mail” or “Incoming/Mail disp.”. p.163
Error Message Explanation and Solution Refer to
Ｃａｕｔｉｏｎ！
Ｔｈｉｓ ＳＭＳ ｉｎｃｌｕｄｅｓ
Ｐｈｏｎｅ Ｎｏｓ. ｏｒ ＵＲＬｓ．
Ｂｅ ｃａｒｅｆｕｌ ｉｆ ｙｏｕ
ｄｏ ｎｏｔ ｒｅｃｏｇｎｉｚｅ
ｔｈｅ ｓｅｎｄｅｒ．
Ｓｃａｎｎｉｎｇ ｆｕｎｃｔｉｏｎ