SUSPENSION
SECTION 14
Page 45
DRESSTA
TD-25M EXTRA
METAL TYPE FACE SEALS
55. SEAL INSPECTION
IMPORTANT:
Do not intermix metal sealing rings; keep original mated rings as a set. Do not
drop, bump or roughly handle these rings. Cleanliness is critical. Do not handle with dirty or
greasy hands.
1. Inspect the condition of the seal metal rings as described in the following steps to determine if
existing kit seal could be reused or if a completely new seal is needed.
1A. Check condition of rubber seal rings. If any sign of wear, scratches, nicks, cuts, etc. replace
complete seal. Inspect condition of metal ring seal surfaces as follows. Highly polished surfaces of
rings must be free of chips, pocks and deep scratches.
1B. The narrow, highly polished sealing band must be within outer half of the sealing face (see
Figs. 14.49 and 14.50).
Fig. 14.49. Metal Ring Acceptable for Rebuild
Fig. 14.50. Metal Ring Acceptable for Rebuild
Arrow (
) shows narrow highly polished sealing
band concentric with I.D. and O.D.
and within outer half of sealing face.
Arrow (
) shows narrow sealing band
within inner half of sealing face.
C – Center of Sealing Face
O.H. – Outer Half of Sealing Face
I.H. – Inner Half of Sealing Face
1C. The narrow band must be uniform and be concentric with the I.D. and O.D. (see
Figs. 14.50 and 14.51).
Summary of Contents for TD-25M EXTRA
