ComAp InteliDrive DCU Industrial Global Manual Download

Page: 133 / 350

InteliDrive DCU Industrial 3.4.0 Global Guide

133

RPMdep protect (AS only)

RPM dependent Oil pressure and Coolant pressure protections are available in AS (propulsion) application only.

Both protections are by default set to Protection block type = RunOnlyBlkDel1 (Engine running - block delay 1).

There are two setpoints for linear Warning limit, two for Shutdown limit and one for delay. Setpoints adjusting

step and range depends on corresponding sensor characteristics.

Note:

The particular RPM dependent protection is fully disabled if both xxxIdlexxx and xxxNomxxx parameters

are set to value 0,0. I.e. the protection is not activated even if measured value is negative (e.g. when there is a

wrong sensor calibration).

Setpoint group

RPMdep protection (AS

only)

Related FW

3.4.0

Range [units]

0.0 .. 10.0 [Bar]

Default value

0.0

Force value

Alternative config

Step

0.1

Comm object

10140

Related applications

Description

Linear Warning characteristic is defined by two points for

Idle RPM (page 118)

and

Nominal RPM (page

104)

. OPIdleRPMWrn defines oil pressure warning level at idle speed.

OPIdleRPMWrn

back to List of setpoints

Summary of Contents for InteliDrive DCU Industrial































































































































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Industrial

Reviews:

Related manuals for InteliDrive DCU Industrial

Brands by name

Popular brands

ComAp InteliDrive DCU Industrial, Global Manual

Search results

Summary of Contents for InteliDrive DCU Industrial

Reviews:

Related manuals for InteliDrive DCU Industrial

Brands by name

Popular brands