ComAp InteliDrive DCU Industrial Global Manual Download

Page: 296 / 350

InteliDrive DCU Industrial 3.4.0 Global Guide

296

Terminator

Cold Junction Compensation (CJC) settings

Please have a look at Cold junction compensation in

Cold Junction Compensation (CJC) (page 323)

chapter.

Technical data

Dimension (W × H × D)

110 × 110 × 46 mm (4.3” × 4.3” × 1.8”)

Weight

237.5 grams

Interface to controller

CAN1

Analog inputs (not electric separated)

8, no galvanic separated

Measuring

±100 mV

Accuracy

± 0.1 % of actual value + ± 100 µV (± 3 °C)

Internal sensor for measuring cold junction - Accuracy

±1 °C in temperature range -20 °C ÷ +70 °C

Galvanic separation

CANbus is galvanic separated from the

measurement and power supply.

All analog inputs are galvanic separated from

power supply.

Analog inputs are not galvanic separated

between channels

Power supply

8 to 36 V DC

Protection

IP20

Current consumption

35 mA at 24 V ÷ 100 mA at 8 V

Storage temperature

- 40 °C to + 80 °C

Operating temperature

- 30 °C to + 70 °C

Heat radiation

2 W

Thermocouples galvanically separated and galvanically non-separated are supported.

back to Extensional modules

Summary of Contents for InteliDrive DCU Industrial































































































































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Industrial

Reviews:

Related manuals for InteliDrive DCU Industrial

Brands by name

Popular brands

ComAp InteliDrive DCU Industrial, Global Manual

Search results

Summary of Contents for InteliDrive DCU Industrial

Reviews:

Related manuals for InteliDrive DCU Industrial

Brands by name

Popular brands