Audi S5 CABRIOLET Owner'S Manual Download Page 180 | Manualshive

Page: 180 / 294

background image

Child safety

178

WARNING

Never install a rearward-facing child safety seat on the front
passenger's seat if the front passenger's airbag has not been deac-
tivated

⇒

page 176. This can result in serious or possibly fatal

injury.

Child safety seats: category 2/3

A suitable child safety seat and a correctly worn seat belt
can protect your child.

Children up to about 12 years of age weighing between 15 and 36 kg
but less than 1.5 metres tall are best protected by a child safety seat

in conjunction with the three-point seat belts

⇒

fig. 188 and

⇒

fig. 189.

Follow the manufacturer's instructions and observe any statutory
requirements when installing and using child restraints

⇒

page 175, “Important safety notes for using child safety seats”.

WARNING

The diagonal part of the belt should be positioned roughly over the
centre of the shoulder and fit closely against the upper part of the
body. It must never be allowed to run across the neck. The lap part
of the belt should fit closely over the hips. It must not be posi-
tioned over the stomach. Pull the belt tight if necessary to take up
any slack.

Note

We recommend that you fit child safety seats with backrests.

Fig. 188 A category
2/3 forward-facing
child seat (with back-
rest) fitted on the rear
seat

Fig. 189 A category
2/3 forward-facing
child seat (without
backrest) fitted on the
rear seat

document_0900452a81793dcc.book Seite 178 Mittwoch, 21. März 2007 5:42 17

«
...
178
179
180
181
182
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

witty park XEV6 Series

Brand: hager Pages: 9

Brand: Vauxhall Pages: 2

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: TBC Pages: 12

Brand: Yakima Pages: 12

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Whispbar Pages: 15

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: GMC Pages: 430

Brand: Oldsmobile Pages: 380

Brand: TAUBENREUTHER Pages: 18

Brand: WABCO Pages: 34

Brand: Club Car Pages: 286

Brand: Volvo Pages: 362

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands