Audi S5 CABRIOLET Owner'S Manual Download Page 272

Page: 272 / 294

Fuses and bulbs

270

Removing rear light

To change the bulbs, you must remove the rear light.
Removing the light requires a certain degree of practical
skill.

– Check which of the bulbs is defective.

– Open the boot lid.

– Remove the side trim.

– Insert the screwdriver (from the tool kit) through the side

opening in the plastic screw

⇒

fig. 252.

– Turn the screwdriver anti-clockwise to loosen the screw

and then carefully remove the screw.

– Gradually ease the light housing out of the rubber

mountings (positions

⇒

fig. 253

and )

pulling

alternately in direction of arrows

and

. If necessary

use the tool for changing bulbs from your vehicle's
toolkit to carefully apply some pressure between posi-
tions

and

⇒

– Unplug the electrical connector.

– Change the defective bulb

⇒

page 271.

Caution

When removing or installing the rear light, take care not to cause
any damage.

•

Removing the rear light in particular can lead to the paintwork or

rear light becoming damaged. This is another reason why we
recommend having the bulbs changed by a qualified workshop.

•

NEVER use metal tools (e.g. a screwdriver) or sharp or pointed

plastic tools to lever out the rear light - risk of damaging the paint.

Note

Make sure you have a soft cloth ready to place under the glass on
the rear light, to avoid any scratches.

Fig. 252 Luggage
compartment: Loca-
tion of retaining screw
for rear light

Fig. 253 Removing
rear light from side
panel

document_0900452a81793dcc.book Seite 270 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands