Audi S5 CABRIOLET Owner'S Manual Download Page 78

Page: 78 / 294

Seats and storage

To maintain safe handling on the road, please observe the
following points:

– Distribute the weight as evenly as possible.

– Position heavy items as far forward as possible

⇒

page 75, fig. 79.

– Secure the load with the luggage net* or with non-elastic

straps secured to the fastening rings*

⇒

page 76.

WARNING

•

Unsecured objects in the luggage compartment can suddenly

shift and cause changes in the handling of the vehicle.

•

In an accident or a sudden manoeuvre, loose objects in the

passenger compartment can be flung forward and possibly injure
vehicle occupants.

•

Always store objects in the luggage compartment and secure

with suitable straps. This is especially important for heavy
objects.

•

When you transport heavy objects, always keep in mind that a

change of the centre of gravity can also cause changes in vehicle
handling.

•

Please observe the important safety warnings

⇒

page 152,

“Safe driving”.

Note

Adjust the tyre pressure to match the vehicle loading - the correct
pressures are specified on the sticker on the end face of the driver's
door.

Applies to vehicles: with fastening rings

Fastening rings

There are four fastening rings in the luggage compart-
ment which can be used to secure loads.

– Use the fastening rings to secure the load

⇒

fig. 80

-arrows-.

– Please refer to the safety notes

⇒

page 159.

Fig. 80 Location of
fastening rings in
luggage compartment

document_0900452a81793dcc.book Seite 76 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands