Audi S5 CABRIOLET Owner'S Manual Download Page 175 | Manualshive

Page: 175 / 294

background image

Airbag system

173

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

control for the garage door). These objects could cause injury if the
head-protection airbag is triggered.

•

The sensors for the airbags are located in the front doors. You

must therefore not make any modifications to the doors or door
trim (e.g. retrofitting loudspeakers), as this could impair the func-
tion of the side airbags. Any damage to the front doors could lead
to faults in the system. Repairs or any other work on the front
doors must therefore always be carried out by a qualified work-
shop.

•

Where sun blinds are fitted on the rear doors, these must not

obstruct or impair the airbags in any way.

•

If unsuitable accessories are installed near the head-protection

airbag, the protection afforded by the airbag can be seriously
impaired if the system is triggered. When the head-protection
airbag opens, parts of these accessories could be thrown into the
vehicle and injure passengers

⇒

page 239.

•

Any work involving the head-protection airbags, or removal

and installation of the airbag components for other repairs (such
as repairs to the roof liner), must always be performed by a quali-
fied workshop. Otherwise the airbag system may fail to work
properly.

Applies to vehicles: with key-operated switch for front passenger's airbag

Deactivating the front passenger's
airbag via the key-operated switch

If an airbag has been deactivated, it should be reactivated
as soon as possible so that it can continue to give the
required protection.

The key-operated switch for deactivating the front
passenger's airbag is located in the glove box

⇒

fig. 184.

– To deactivate the front passenger's airbag, insert the

ignition key into the switch and turn it to position

.

WARNING (continued)

Fig. 184 Key-operated
switch in glove box for
deactivating front
passenger's airbag

Fig. 185 Lamp indi-
cates that front
passenger's airbag has
been deactivated via
key-operated switch

A

OFF

document_0900452a81793dcc.book Seite 173 Mittwoch, 21. März 2007 5:42 17

«
...
173
174
175
176
177
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Camcar Pages: 6

Brand: Jeep Pages: 42

Brand: Jeep Pages: 44

Brand: Cadillac Pages: 20

Brand: Jeep Pages: 7

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 354

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 10

2013 Escalade ESV

Brand: Cadillac Pages: 524

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Cadillac Pages: 450

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

Brand: Cadillac Pages: 78

Brand: Cadillac Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands