Audi S5 CABRIOLET Owner'S Manual Download Page 250

Page: 250 / 294

Self-help

248

The TMS can be used at outside temperatures down to – 20 °C.

WARNING

After repairing a tyre please note the following points:

•

Do not drive faster than 80 km/h.

•

Avoid heavy acceleration, hard braking and fast cornering.

•

Vehicle handling could be impaired.

•

Tyres which have been sealed using the TMS are only suitable

for temporary use. Damaged tyres must be renewed.

•

The TMS must NOT be used,

−

on cuts and punctures larger than 4 mm

−

if the wheel rim has been damaged

−

if you have been driving with very low pressure or a

completely flat tyre

•

Seek professional assistance if the repair of a tyre puncture is

not possible with the sealing compound.

•

Do not allow the sealant to come into contact with your eyes,

skin or clothing.

•

If you do come into contact with the sealant immediately rinse

the eyes or skin affected with clean water.

•

Change clothing immediately if it becomes soiled with the tyre

sealant.

•

Make sure you do not breathe in the fumes!

•

If any of the tyre sealant is accidentally ingested, immediately

rinse the mouth thoroughly and drink lots of water.

•

Do not induce vomiting. Immediately contact a doctor!

•

If any allergic reactions should occur get medical help immedi-

ately.

•

Keep the sealant away from children.

For the sake of the environment

Used bottles of sealing compound can be returned to an Audi dealer
for disposal.

Note

•

If sealant should leak out, leave it to dry. When it has dried, you

can pull it off like a piece of foil.

•

Observe the expiry date stated on the sealing compound can.

Have the sealing compound exchanged by a qualified workshop.

Repairing a tyre

Preparations

– If you have a flat tyre, stop the car well away from moving

traffic.

– Apply the parking brake to stop the vehicle moving acci-

dentally.

– Engage first gear.

– Check whether a repair is possible using the Tyre

Mobility System

⇒

page 247.

Fig. 228 Repairing a
tyre

document_0900452a81793dcc.book Seite 248 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands