manualshive.com logo in svg

Audi S5 CABRIOLET, Owner'S Manual

The Audi S5 Cabriolet's Owner's Manual is available for free download on manualshive.com. This comprehensive manual provides essential information and guidance on operating and maintaining your Audi S5 Cabriolet. Get the most out of your vehicle's features and ensure a smooth driving experience with this informative manual.

Share
Download
background image

Driver information system

35

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

Note

On some models the speed limit warning 1 

 and speed limit 

warning 2 

 will also be displayed as yellow symbols. These always 

appear as a small symbol at the top of the display 

⇒

page 28.

Applies to vehicles: with advanced key

Key not in vehicle 

 Key not in vehicle 

This message will appear together with the symbol 

 if the remote 

control key is removed from the vehicle while the engine is running. 
This is to remind you not to continue driving without the key (for 
example if you change drivers).

If the remote control key is not in the vehicle you will not be able to 
switch on the ignition or restart the engine after it has been 
switched off. You will also not be able to lock the vehicle from the 
outside.

Light sensor/ rain sensor defective 

 Automatic headlights/ automatic wipers defective

If the 

 symbol appears, this means that the light sensor/ rain 

sensor is not functioning. For safety reasons, the dipped beam 
headlights will then be switched on permanently when the light 
switch is set to the AUTO position. However, you can still switch the 
lights on and off in the normal way with the light switch. If the rain 
sensor is defective, the functions operated via the windscreen wiper 
lever will still be available. You should have the light sensor/ rain 
sensor checked by a qualified workshop as soon as possible.

Brake pads worn

⇒

page 36

Battery power*

⇒

page 36

Bulb monitor*  
Bulb failure*

⇒

page 36

Check engine oil level

⇒

page 37

Engine oil sensor defective

⇒

page 37

Fuel level low

⇒

page 36

Washer fluid level low*

⇒

page 36

advanced key*  
Key not in vehicle

⇒

page 35

Light sensor/ rain sensor defec-
tive

⇒

page 35

Dynamic headlight range con-
trol* defective

⇒

page 37

Battery in remote control key

⇒

page 39

Electro-mechanical
parking brake

⇒

page 121

adaptive light* defective

⇒

page 37

Ignition lock defective

⇒

page 37

Windscreen wiper defective

⇒

page 37

document_0900452a81793dcc.book  Seite 35  Mittwoch, 21. März 2007  5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Brand: Daihatsu Pages: 43
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Brand: Porsche Pages: 144
Yescom YES5062 User Manual preview
YES5062
Brand: Yescom Pages: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Brand: Z Automotive Pages: 16
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
Skoda Fabia II 2007 Workshop Manual preview
Fabia II 2007
Brand: Skoda Pages: 165
Prorack K947 Fitting Instructions Manual preview
K947
Brand: Prorack Pages: 14
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Brand: Charge Amps Pages: 14
Cadillac CTS 2011 Manual preview
CTS 2011
Brand: Cadillac Pages: 78
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Brand: chinavasion Pages: 3
pewag forstgrip Mounting Instruction preview
forstgrip
Brand: pewag Pages: 52
TrailPRO TPRGBW4 Quick Start Manual preview
TPRGBW4
Brand: TrailPRO Pages: 3
Truma Mover smart M Operating Instructions Manual preview
Mover smart M
Brand: Truma Pages: 84
SoundMax SM-DVR77FHD Instruction Manual preview
SM-DVR77FHD
Brand: SoundMax Pages: 20
Yutrax TX106 Operator'S Manual preview
TX106
Brand: Yutrax Pages: 8
caron PHC-9000 User Manual preview
PHC-9000
Brand: caron Pages: 10
Volkswagen Passat 1995 Official Factory Repair Manual preview
Passat 1995
Brand: Volkswagen Pages: 307
Guardsman G1510 Fitting Instruction preview
G1510
Brand: Guardsman Pages: 3

Brands by name

Popular brands

Load more brands