Audi S5 CABRIOLET Owner'S Manual Download Page 260 | Manualshive

Page: 260 / 294

background image

Self-help

258

Do not pull too hard with the towing vehicle and take care to avoid
jerking the towrope. When towing on a loose surface there is always
a risk of overloading and damaging the anchorage points.

Caution

If there is no oil in the gearbox or no lubricant in the automatic
transmission the car may only be towed with the driven wheels
lifted clear of the road, or transported on a special car transporter
or trailer.

Note

•

Note the regulations concerning towing.

•

The hazard warning lights of both vehicles must normally be

switched on. However, observe any regulations to the contrary.

•

Make sure that the towrope is not twisted, as otherwise the front

towline anchorage on your vehicle could work itself loose.

Front towline anchorage

The front towline anchorage is only mounted if the vehicle
has to be towed.

The screw connection for the towline anchorage is located
behind a cover cap on the right side of the front bumper.

– Take the towline anchorage out of the vehicle's tool kit

⇒

page 245.

– To detach the cover cap from the bumper, firmly press

the lower part of the cap inwards to release it

⇒

fig. 238.

– Screw the towline anchorage firmly all the way into the

screw connection

⇒

fig. 239.

After use, unscrew the towline anchorage and put it back in the
toolbox. Replace the cap in the bumper. The towline anchorage
should always be kept in the vehicle.

WARNING

If the towline anchorage is not screwed in as far as the stop, there
is a risk of the screw connection shearing off during towing (acci-
dent risk).

Fig. 238 Front
bumper: Cover cap

Fig. 239 Front
bumper: Fitting the
towing eye

document_0900452a81793dcc.book Seite 258 Mittwoch, 21. März 2007 5:42 17

«
...
258
259
260
261
262
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: Ford Pages: 2

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: BMW Pages: 21

Brand: STARLANE Pages: 24

Brand: iOttie Pages: 58

Brand: tams elektronik Pages: 19

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Brand: Porsche Pages: 146

Brand: Lincoln Pages: 538

Brand: Smappee Pages: 28

Brand: Nos Pages: 22

Brand: Sanixair Pages: 20

OMNI-BIKE plus Caravan Special

Brand: OMNISTOR Pages: 4

Brand: Erich Jaeger Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands